Laynie Hasan.

← All offer guides

Sewing & Craft Comparisons · Reviewed November 4, 2026

Clover 12mm vs 18mm: Which Bias Tape Maker Size?

A pattern asking for quarter-inch double-fold binding does not call for a quarter-inch tape maker. Clover labels these tools by the width of the single-fold tape that comes out, before you fold it in half again. The regular 464/12 makes nominal 12mm, or half-inch, tape; the 464/18 makes nominal 18mm, or three-quarter-inch, tape. That distinction matters more than the size of the little tool. Start with the edge you want to finish, then work backward through the folds.

Best for

A sewist making matching or contrasting fabric binding who needs to choose between a narrow edge and a more visible band.

Probably not for

Someone expecting a powered machine, an iron, ready-made tape or a tool that cuts strips and stitches them onto the garment.

Specifications at a glance

Manufacturer specifications for the exact versions compared
Width and workflowClover 464/12Clover 464/18
Nominal single-fold output12mm / 1/2 inch18mm / 3/4 inch
After an additional fold in halfApproximately 6mm / 1/4 inch, before wrapping an edgeApproximately 9mm / 3/8 inch, before wrapping an edge
Metric cut-strip guide: medium-weight cloth23mm, per Clover’s instruction chart35mm, per Clover’s instruction chart
Metric cut-strip guide: lightweight cloth28mm, per Clover’s instruction chart40mm, per Clover’s instruction chart
Materials listed by CloverPolymethyl pentane and ironPolymethyl pentane and iron
Type and selected packageRegular non-fusible maker; one toolRegular non-fusible maker; one tool

As an Amazon Associate I earn from qualifying purchases.

Clover 464/12 regular 12mm bias tape maker

The smaller of these two makers suits a narrow outline rather than a wide decorative border. Fold its nominal half-inch single-fold output in half again and you are working with roughly quarter-inch double-fold tape. That is a useful starting point for a pattern specifying that binding width, provided your fabric and the edge thickness leave enough room for attachment.

Pros

  • Produces the narrower of the two bands without buying the wider tool and refolding its tape
  • Requires a narrower cut strip than the 18mm tool for the same cloth category

Cons

  • Less width to wrap around a bulky edge and still catch both folded sides
  • A small visible band may hide most of a large fabric print

Who it’s for: Choose 464/12 when the pattern and a scrap sample support a narrow binding. Skip it for a project that needs three-quarter-inch single-fold tape or a broader wrapped border.

Check Clover 464/12 regular 12mm bias tape maker on Amazon

Clover 464/18 regular 18mm bias tape maker

The 18mm maker leaves a wider strip after both raw edges have been turned inward. An additional lengthwise fold produces roughly three-eighths-inch double-fold tape. It makes sense when that wider band is part of the design or the sample needs more fabric around the edge. It is not an adjustable tool that also produces the 12mm size.

Pros

  • More room across the tape for a visible fabric motif or contrasting border
  • More width available for wrapping an edge than the 12mm output

Cons

  • Uses a wider raw strip and covers more of the project beside the edge
  • The wider finish can be too prominent for a narrow neckline treatment

Who it’s for: Choose 464/18 for a pattern calling for its single-fold width or a wider double-fold finish. Pass if you need a discreet quarter-inch outline without doing extra manual refolding.

Check Clover 464/18 regular 18mm bias tape maker on Amazon

Name all three widths before ordering

There are three measurements on the worktable: the raw strip you cut, the tape after its two long edges are folded inward, and the tape after another fold brings those long folded edges together. Clover’s 12mm and 18mm labels refer to the middle measurement. The second lengthwise fold is a separate pressing step. Neither tool produces a permanently closed strip just by pulling the cloth through it.

If your pattern says half-inch single-fold tape, the 12mm tool is the corresponding nominal size. If it says half-inch double-fold tape, neither tool here is the matching size. Do not buy the half-inch maker just because that number appears in both descriptions. Likewise, the 18mm maker corresponds to three-quarter-inch single-fold tape, not three-quarter-inch binding visible on each face of the finished project.

The approximate 6mm and 9mm widths in the table are simply half of the nominal metric output, not measured results from a sewing test. Clover notes that fabric type can change the finished tape width. Wrapping the tape over an edge also uses some of its width around that edge. A thick stack of fabric may leave less coverage on either face than a thin sample, so measure the actual bound sample before cutting the rest of your strips.

Choose the line you want the binding to draw

For a plain cotton top with a contrasting neckline, lay narrow paper strips beside the neckline on the pattern or an existing garment. Compare the approximate quarter-inch and three-eighths-inch bands visually. One may read as a thin outline while the other becomes an obvious trim. This is a design decision, not evidence that either maker performs better. If the pattern specifies a seam allowance and binding method, retain those instructions rather than substituting a width solely because the color looks good.

A placemat or unpadded fabric organizer can pose the opposite question: perhaps the border is meant to repeat a color elsewhere in the room. The 18mm maker gives that border more room. Check the scale of a print, too. Cut a small window in paper the width of the visible band and move it across the cloth. A tiny check may remain recognizable through either window, while a large flower can disappear into an apparently random patch of color. That preview can save a disappointing fabric choice regardless of which maker you buy.

For a padded or heavily layered item, do not assume that the larger of these two tools is automatically large enough. Wrap a trial strip around the same layers and check both faces. If the rear folded edge barely reaches the stitching line, there is not enough margin for that construction. Consider a wider binding method specified by the pattern instead of trying to make the 12mm or 18mm tool serve every project.

Match the cut strip to the fabric, not just a formula

Clover’s general explanation describes cutting a strip about twice the single-fold width. Its detailed instruction chart is more useful at the cutting table because it distinguishes medium-weight cloth, such as cotton, from lightweight cloth, such as lining. The metric entries are 23mm and 28mm for the 12mm maker, versus 35mm and 40mm for the 18mm maker. Those are starting widths from the manufacturer’s chart, not a promise that every fabric will fold identically.

Work in one unit system and use the chart supplied with your tool. Cut one short sample before making a whole pile of strips. Look at whether both edges turn inward consistently and whether the emerging tape stays the intended width. A fabric that will not feed neatly is a reason to check the cut width and the instructions, not to keep pulling harder. Make the trial from the actual binding cloth; a convenient cotton offcut does not settle how a different lining fabric will behave.

For curved-edge binding, Clover instructs cutting at 45 degrees to the fabric grain. Straight-grain strips remain useful for its tape-cloth craft applications, but passing them through the maker does not turn them into bias-cut fabric. If you use a rotary cutter for the strips, the OLFA RTY-2/G vs RTY-2/DX guide compares two handle and blade-cover arrangements. A straight, consistent strip is still your responsibility whichever cutter or tape maker you choose.

Plan the pressing and sewing as separate jobs

These are passive folding guides. You supply the cloth, a suitable pressing surface and an iron, and you move the maker while pressing the folds that emerge. The iron in Clover’s materials list means the tool contains iron as a material; it does not mean an electric iron comes in the package. Keep the hot soleplate away from the maker itself, and follow the cloth’s pressing requirements. More heat is not a remedy for using the wrong strip width.

Before working on a long strip, arrange the board so the unpressed cloth can feed without catching on the edge and the pressed section has somewhere to lie. Clover’s instructions show pinning the starting end and drawing the maker along as you iron. A pointed leading end can help get the strip started. Once the folds are set, add the center fold separately if you need double-fold tape, then check the result against the edge sample.

Attachment is another stage. Neither maker holds the binding on the project or ensures that a seam catches its back edge. Pin or clip the sample and inspect underneath before continuing. The Clover Wonder Clips vs Mini guide addresses holding space beside a narrow seam; it does not replace checking the binding’s reach. If you are repeatedly missing the rear edge, revisit the fold alignment, width and pattern method before blaming the folding tool.

Buy for the next edge, not every possible project

For a recurring quarter-inch double-fold finish on suitable fabric, start with 464/12. For a three-eighths-inch double-fold finish or a three-quarter-inch single-fold strip, start with 464/18. If the project calls for fusible tape that can be positioned with adhesive before stitching, these regular 464-series models are not Clover’s separate fusible-maker line. Check that distinction in the product name as well as the width.

You may not need either tool for one short repair. Hand-pressing a small strip or using ready-made tape in the correct width can finish that job without adding another notion. A dedicated maker becomes more relevant when you repeatedly want binding from a particular garment fabric, print or color. Pick the width that meets the next real pattern, prove it with one scrap edge, and only then commit to making all the tape.

Official sources and further reading

Sources reviewed on November 4, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.