Music & Hobby Comparisons · Reviewed November 4, 2026
Dunlop 210 vs 215: Which Medium Glass Guitar Slide Fits?
Both slides say medium, and both have a 20 mm opening. So if a Dunlop 210 slips off your little finger, a 215 is not a tighter size. What changes is the glass around that opening: the 210 is shorter and slimmer; the 215 is longer and has a heavier wall. Choose the 210 if you want less tube in the way when you switch back to fretted notes. Choose the 215 if you have a specific use for the extra length across the strings and room for the larger barrel beside your other fingers.
Best for
A guitarist who wants a finger-worn glass slide and is deciding between the medium-wall 210 and heavy-wall 215, particularly when both seem to fit the same finger.
Probably not for
Someone looking for a smaller or larger finger opening, a metal slide, or a solid bar to hold above the strings of a lap steel.
Specifications at a glance
| What Dunlop specifies | 210 medium wall | 215 heavy wall |
|---|---|---|
| Material and fit class | Glass, medium | Glass, medium |
| Inside diameter | 20 mm | 20 mm |
| Outside diameter | 25 mm | 29 mm |
| Length | 60 mm | 69 mm |
| Ring size listed by Dunlop | 10 to 11 | 10 to 11 |
| Linked US package | One 210 slide | One 215 slide |
As an Amazon Associate I earn from qualifying purchases.
Dunlop 210 medium-wall medium glass slide
The 210 puts a 25 mm barrel around the same opening as the 215. Picture the ring finger wearing the slide and the little finger resting beside it: this is the less bulky of the two at that point of contact. Its 60 mm length is also worth considering if a longer tube bumps into the base of the finger or projects past the fingertip farther than you like.
Pros
- Smaller outside diameter leaves more room beside the slide finger
- Shorter tube to position when alternating slide phrases and fretted notes
Cons
- Nine millimeters less length available to span the strings
- Does not give a smaller finger a snugger opening than the 215
Who it’s for: Look here first for a song with a short slide fill between fretted chords. Pass if the reason you are replacing your present 60 mm slide is that you frequently run out of length.
Check Dunlop 210 medium-wall medium glass slide on Amazon Paid linkDunlop 215 heavy-wall medium glass slide
The 215 adds glass outside the finger and extends the tube to 69 mm. That gives you more length to position across a group of strings without changing the nominal bore. It makes sense if you know you like this finger fit but want more margin at the ends. A player who already finds their slide rubbing the next finger should pay attention to the larger diameter before choosing it.
Pros
- Longer span for a part that calls for several strings together
- Retains the 20 mm bore for someone moving from a 210
Cons
- Larger exterior takes up more room beside adjacent fingers
- Extra length can be unnecessary for isolated notes on one string
Who it’s for: Consider it for a repeated broad chord shape or as a longer alternative to a well-fitting 210. Do not buy it to correct a loose bore or simply because heavy sounds like a more advanced specification.
Check Dunlop 215 heavy-wall medium glass slide on Amazon Paid linkStart with the finger that will actually wear it
Take a passage you already play and form the chord immediately before the slide enters. Which finger could wear a tube and still leave you the notes you need? A slide on the little finger leaves the ring finger available, whereas wearing it on the ring finger changes which fingers you can readily use for the chord. A ring size taken from the other hand, or even the next finger on the fretting hand, answers the wrong buying question.
Dunlop gives both the 210 and 215 a ring-size range of 10 to 11 and recommends a slide slightly larger than your ring size, with the final choice depending on how you play. Its dimensions are nominal because these slides are handmade. If possible, try a medium on the intended finger with your hand in playing position. Can you put it on and take it off comfortably? Does it stay where you want it as you turn your wrist? If the problem is inside the tube, set both of these models aside and try another bore.
If you already own a comfortable slide, measure the opening across the inside, not from one outside edge of the glass to the other. A slide that measures 25 mm across the outside is not necessarily a match for a finger that needs a 25 mm opening. Write down all three measurements of the one you own: inside diameter, outside diameter and length. That way you can keep the feature that works while deliberately changing the one that does not.
Measure across the strings where the part is played
Imagine the last note of a tune as a chord on several strings. The length of the slide matters across that group of strings, not along the length of the guitar neck. With the instrument set down, measure from the first string you intend to sound to the last at the fret where you play the chord. Do not borrow the nut width from a guitar specification sheet: that is a different location and includes the edges of the neck. The useful question is how far apart the actual strings are under your hand.
Mark 60 mm and 69 mm on strips of paper. Hold each strip above those strings at the angle you normally use. Do you have some room at both ends, or do you have to line up one edge exactly to keep the other outside string under the strip? Do not assume every millimeter of a rounded glass end will give the same contact as the middle of the tube. This exercise helps you decide whether another nine millimeters would do anything for that chord. Paper cannot tell you how the slide will feel on the finger.
Now repeat the thought experiment on a fill played on just the two highest strings. Both slides may have plenty of length, and the real job may be keeping the unused strings quiet. Buying the longer model because it covers more territory does not solve that problem. Choosing the shorter one does not automatically mute anything either. Look at the material you plan to play most, rather than buying for a full-width chord that never appears in your set.
Check the transition out of the slide phrase
Players often picture the gliding note and forget the beat immediately after it. If the next note is fretted with a neighboring finger, hold that shape while the slide finger stays out of the way. The 215 is four millimeters greater in outside diameter, which means two millimeters more glass extends outward on each side from the same center. Where two fingers sit close together, that is the relevant difference. If the next chord is on the far side of the neck and the slide projects beyond your fingertip, consider the length as well.
For a part played entirely with the slide, that compromise looks different. You may not need the adjacent fingers for a quick change of chord shape at all. The longer 215 then earns its space if it makes the placement across the strings less exacting for your own hand. Neither comparison predicts a measured difference in sustain or guarantees a particular recording sound. Both products are glass; it is more useful to identify a clearance or coverage problem than to order by a description such as “blues tone.”
Separate a fit problem from a tuning problem
If a slide fits comfortably and reaches the right strings but the chord sounds wrong, check the tuning named in the arrangement before changing hardware. A straight slide across several strings does not turn standard tuning into an open chord tuning. The D’Addario Micro vs Eclipse tuner comparison is useful if you need a way to check the open strings; a tuner you already own can do the same job. Neither the 210 nor the 215 changes the interval between those strings for you.
Also distinguish moving a note during a phrase from moving the starting key of a whole song. A slide travels with the fretting hand. If the actual instruction is “capo at the second fret” and you need both hands free for ordinary chords, you are looking for a different accessory. The D’Addario vs Kyser acoustic guitar capo guide covers that decision. For an actual slide part, order by number as well as size: 210 for the slimmer 60 mm tube, 215 for the heavy-wall 69 mm tube. Check that the listing is for one slide, not a sampler pack with several finger sizes.
Official sources and further reading
Sources reviewed on November 4, 2026. Prices, availability and terms can change; recheck before buying.
Commission disclaimer
This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.