Music & Hobby Comparisons · Reviewed November 10, 2026
Radial ProDI vs Pro48: Which Direct Box Fits Your Rig?
For a keyboard’s mono output or a bass pedalboard visiting unfamiliar mixers, take the passive ProDI: it runs even when the venue cannot give you phantom power. For a lower-output passive bass plugged straight into the box, choose the active Pro48 if the engineer can supply 48 volts. Both let you keep your stage amp while sending one mic-level signal to the house.
Best for
A player or sound engineer sending one instrument to a mixer or mic preamp over XLR, with the option of keeping an amp onstage.
Probably not for
Anyone who needs to retain a stereo keyboard part in two mixer channels, record directly over USB, or capture the sound of a guitar speaker.
Specifications at a glance
| Connection or control | Radial ProDI | Radial Pro48 |
|---|---|---|
| Radial part number | R800 1100 00 | R800 1105 00 |
| Circuit and power | Passive transformer; needs no power | Active circuit; requires 48V phantom power |
| Input impedance | 140 kilohms | 220 kilohms |
| Stage connections | Quarter-inch input and thru; balanced mono XLR out | Quarter-inch input and thru; balanced mono XLR out |
| Input pad | Switchable 15 dB cut | Switchable 15 dB cut |
As an Amazon Associate I earn from qualifying purchases.
Radial ProDI Passive Direct Box
A transformer provides a balanced, isolated mic-level feed without a battery, wall supply or power from the mixer. The mono ProDI is distinct from the two-channel ProD2.
Pros
- Can move between stage boxes without checking for phantom power
- Good match for a strong keyboard or preamp output
Cons
- Lower input impedance of the two when connecting a passive pickup directly
- One unit cannot send left and right keyboard channels separately
Who it’s for: For a keyboard player running mono, or a venue that wants a direct box for powered instruments with no power setup of its own.
Check Radial ProDI Passive Direct Box on Amazon Paid linkRadial Pro48 Active Direct Box
The active input presents a lighter load than the ProDI to a pickup connected directly. An indicator on the box shows whether phantom power is reaching it.
Pros
- Higher input impedance suits a lower-output passive magnetic pickup
- Input pad also allows use with hotter sources
Cons
- No battery fallback when the mic input cannot supply 48V
- Not a dedicated high-impedance preamp for a bare piezo pickup
Who it’s for: For a bassist taking the instrument straight to a known phantom-capable mixer, especially when a stage amp also needs a feed.
Check Radial Pro48 Active Direct Box on Amazon Paid linkWhat is on the other end of the short cable?
A bassist brings the same instrument to two shows. At one, the bass cable goes straight into the direct box. At the other, the cable that reaches the box comes from the output of a powered bass preamp. The pickups have not changed, but the source driving the DI has. In the first setup the pickups themselves have to drive the input. In the second, the preamp sits between them and the box. That last connection is more useful for choosing a DI than the name on the bass headstock.
Radial lists an input impedance of 220 kilohms for the Pro48 against 140 kilohms for the ProDI. The larger number means less electrical load on a pickup, not that the part will sound louder through the PA. If a passive bass goes straight in and its attack is what you want to preserve, that difference favors the Pro48. A keyboard or a bass with a working onboard preamp puts a different source on the jack. There the ProDI’s ability to run without power is often worth more than the higher input impedance.
Ask about the actual mixer channel
On a stage plot, write “bass DI, 48V required” beside the Pro48. Phantom power travels from the microphone input back to the box over the XLR cable. It does not arrive through the instrument lead from a powered keyboard or a bass with a fresh battery. Ask the person running the board whether that particular input can supply it. A mixer may switch phantom for a group of channels together; let the engineer decide whether it can be enabled with the other equipment on those channels.
This question can settle the purchase before you compare either circuit. Suppose you use your own mixer for most jobs but plug into a different installed system each Sunday. If nobody can confirm power there and your source is a keyboard, the passive ProDI is the practical choice. If you own the whole path and always patch a passive bass into the same phantom-capable mic input, the Pro48 has no such disadvantage. With the channel muted, make the connections before enabling phantom; the indicator on the Pro48 lets the player and engineer confirm power at the stage end.
Keep the amp feed separate from the house mix
Put the DI near the instrument or pedalboard. Run a short instrument cable into INPUT, take THRU to the instrument input on the stage amp if you use one, and connect the XLR output to the mixer’s mic input. Use the long cable for that last, balanced leg. To choose its length, measure down to the floor and around the playing area, not across the air between two jacks. The Hosa 10-foot and 25-foot XLR cable comparison works through that measurement.
Now decide what the audience should hear. With a bass plugged straight into the DI and a drive pedal between THRU and the amp, stepping on the pedal changes the stage sound only. If the drive is part of the arrangement, put that pedal ahead of the DI so the house gets it too. Neither box hears the loudspeaker, the room or the amp’s tone controls when you wire it this way. If the engineer needs that sound as well as the direct signal, plan a second source and channel instead of looking for a different pad setting.
Count channels before choosing a keyboard DI
A quarter-inch input next to another quarter-inch jack can look like a left-right pair from across a dark stage. Read the legends: INPUT and THRU are not left and right. If the keyboard manual identifies a specific L/MONO output for single-cable use, take that output to one DI. Play the patch that matters most, not just the default piano. Listen to what happens to an effect that normally moves across the stereo field and decide whether the mono version still serves the song.
If the arrangement needs two distinct sides, reserve two DI channels and two mixer inputs, or select a stereo direct box. Do not route left to INPUT and right to THRU expecting the box to mix them. Consider a split-keyboard patch too: if bass is assigned only to the left output and strings only to the right, handing the engineer a cable from just one side could leave an entire instrument out. Decide which outputs the patch actually uses before you spend time choosing between active and passive electronics.
Distorted peaks, steady hum and silence are different clues
Set levels with the loudest sound you plan to use. A quiet verse played on one pickup is a poor check for the chorus after a boost pedal comes on. If the mixer input is clipping, start with its gain control. If the signal still breaks up even though the mixer input has room, try the DI’s pad, then reset mic gain and compare the same phrase at roughly the same listening level. Both boxes provide a 15 dB input cut. Leaving it on for a weak pickup means making up level at the mixer without first establishing that you needed the cut.
A steady hum that appears when you add the stage amp suggests a different check. Try the DI’s audio ground-lift switch; change only that switch and listen. It addresses a possible loop between connected audio devices, not hiss from a pedal or a buzz already coming from the instrument. Leave the protective earth on the amp’s power plug alone. Silence on the Pro48 calls for a simpler first look: is its phantom indicator lit? If it is dark, check the XLR path and console channel with the engineer before chasing the instrument’s tone settings.
When an extra box can stay off the shopping list
If you record a single bass at arm’s length from an interface, start with the interface’s instrument input. A DI becomes useful when you need something that connection does not give you: a long balanced run, an isolated feed with the ProDI, or an amp fed at the same time. The Scarlett Solo and AudioBox GO interface comparison describes the mic and instrument connections on two common desktop setups. Neither Radial replaces an interface’s connection to the computer.
An acoustic instrument with a raw piezo pickup is another reason to pause. A transducer wired straight to an endpin jack and a guitar with a battery-powered onboard acoustic preamp can look alike once the cable is plugged in. Check the pickup maker’s recommended input impedance for the former; it may call for a much higher value than either DI provides. For the latter, assess the preamp output as the source. A label on the instrument case noting the pickup, usual output jack and phantom requirement is more useful on the next changeover than simply writing “bring DI.”
Official sources and further reading
Sources reviewed on November 10, 2026. Prices, availability and terms can change; recheck before buying.
- Radial: ProDI part number, transformer, power and connectors
- Radial: Pro48 part number, active circuit, input impedance and power
- Radial: comparing lower-output instruments and hot sources
- Radial: parallel thru connection, pad and stereo summing limits
- Radial: Pro48 wiring, phantom indicator, gain checks and ground lift
- Radial: ProDI instrument setup, isolation and passive piezo guidance
- Amazon US: standalone Radial ProDI passive direct box Paid link
- Amazon US: standalone Radial Pro48 active direct box Paid link
Commission disclaimer
This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.