Laynie Hasan.

← All offer guides

Cycling Gear Comparisons · Reviewed November 15, 2026

SKS Raceblade Pro vs Pro XL: Which Road Mudguards Fit?

Start with the tires and the space around them. Raceblade Pro suits narrower road tires up to 25 mm; Pro XL is specified for 25 to 32 mm tires and has longer profiles. Both use adjustable, strap-mounted fittings, so neither is a universal answer for every frame.

Best for

Road riders comparing removable front-and-rear mudguards for a compatible 700c bike, especially where permanent fender mounting is not wanted.

Probably not for

Tires wider than 32 mm, a guaranteed fit on every carbon or aero frame, or installation without checking the manufacturer clearance requirements.

Specifications at a glance

Manufacturer specifications for the exact versions compared
Documented featureRaceblade ProRaceblade Pro XL
Compared finish and articleShiny black, 11319Shiny black, 11322
Wheel size700c / 28 inches700c / 28 inches
Tire widthUp to 25 mm; regional lower limit differs25 to 32 mm
Front fender length519 mm565 mm
Rear fender length680 mm730 mm
MountingQuick-release straps; adjustable staysQuick-release straps; adjustable stays
Body materialPlasticPlastic
Disc brakesCompatible subject to routing and clearance checksCompatible subject to routing and clearance checks

As an Amazon Associate I earn from qualifying purchases.

SKS Raceblade Pro Fender Set, Shiny Black 11319

The narrower road-bike set, with a 519 mm front profile and 680 mm rear profile.

Pros

  • Specified for road tires up to 25 mm
  • Shorter front and rear profiles
  • Removable strap mounting with adjustable stays

Cons

  • Not specified for tires above 25 mm
  • Regional pages disagree on the minimum tire width
  • Requires a frame-specific clearance check

Who it’s for: Consider it for a compatible narrow-tire road bike. Skip it for 28 mm tires or when you cannot maintain the required clearances.

Check SKS Raceblade Pro Fender Set, Shiny Black 11319 on Amazon

SKS Raceblade Pro XL Fender Set, Shiny Black 11322

The 25 to 32 mm tire option, with longer 565 mm front and 730 mm rear profiles.

Pros

  • Documented 25 to 32 mm tire range
  • Longer profiles than the standard Pro
  • Uses the same removable mounting approach

Cons

  • Not specified for tires above 32 mm
  • Longer profiles still need room on your bike
  • XL does not mean universal gravel-bike compatibility

Who it’s for: Consider it for compatible 25 to 32 mm road tires. Skip it when your wider tires or frame geometry fall outside the documented fit.

Check SKS Raceblade Pro XL Fender Set, Shiny Black 11322 on Amazon

Let tire width narrow the decision first

The most useful difference is not the XL label by itself. SKS specifies the Raceblade Pro for tires up to 25 mm and the Pro XL for tires from 25 to 32 mm. A rider choosing mudguards for a 28 mm setup therefore has a different starting point from someone keeping a narrow-tire road bike on 23 mm tires. Choose the relevant size range before comparing profile lengths.

There is a regional specification wrinkle at the narrow end. SKS USA lists the standard Pro for 18 to 25 mm tires, while the German product page lists 20 to 25 mm. Both agree on the 25 mm ceiling. This guide does not silently expand the range: owners of 18 or 19 mm tires should confirm the exact application with SKS before ordering.

Record the wheel and tire setup you actually intend to use, including any planned tire change. If you are also replacing your inflation equipment, the Topeak JoeBlow Sport III and Lezyne Macro Floor Drive comparison covers that separate purchase. Do not turn an accessory decision into a reason to use a tire setup your bicycle does not support.

Treat 25 mm as an overlap, not an automatic XL recommendation

A 25 mm tire appears in both documented ranges. At that boundary, the width label alone cannot select the set. Look at the actual bicycle, the space available for the profiles and the way you want to use removable mudguards. If you are uncertain about the installed tire size or the proposed mounting points, ask a competent bicycle mechanic to assess the complete arrangement.

The XL front profile measures 565 mm rather than 519 mm, and its rear profile measures 730 mm rather than 680 mm. Those differences are 46 mm at the front and 50 mm at the rear. They describe component length, not a measured percentage improvement in splash protection. Where the profile sits on your bicycle matters too.

Consider future plans without buying imaginary compatibility. Moving from a compatible 25 mm setup to a supported 28 mm setup would make the XL range relevant, but only if the bicycle and complete installation also work. Conversely, buying XL for a 23 mm tire because it sounds more comprehensive moves outside its stated range. There is no need to make the larger model the default.

Quick removal does not remove the initial fitting work

Both products use a double-jointed quick-release fitting system with adjustable stays. This makes the mounting arrangement central to the comparison: you are choosing a removable set that still needs to be positioned for a particular bicycle. Think of the first fitting as a separate job from taking a correctly adjusted set off for storage or transport.

Before buying, look at where the fittings would sit and what already occupies those areas. Brake routing and other accessories can matter more than a clean-looking product photograph. SKS describes compatibility with disc brakes and aero forks, but those category descriptions should not be read as a guarantee for every bicycle within either category. Identify the exact obstruction or uncertainty before committing.

Be realistic about your routine. If the guards will come off after each wet ride, decide where both pieces will dry and be stored. If they will remain installed through a season, access for inspection and cleaning still belongs in the plan. Also check how you normally transport the bike; do not assume that an installed accessory will suit every rack or storage position.

Use clearance requirements as a go-or-no-go check

The SKS manual covering these article numbers requires at least 15 mm between mudguard and tire. It also specifies 10 mm clearances at the relevant brake, frame, fork and downtube locations. These are fitting requirements, not optional targets to trade away for a closer-looking installation. Read the illustrated manual for the complete positioning procedure rather than using this comparison as installation instructions.

Disc-brake compatibility comes with a routing check, and the guards must not interfere with moving brake parts. SKS also requires checking the fitted guards before each ride. If you cannot establish the prescribed clearance, or an adjustment leaves interference elsewhere, stop and have the fit assessed. Switching from standard to XL does not by itself solve a mounting conflict.

The practical buying question is whether your bike can accommodate the whole fitted assembly. A tire width printed in a table answers only one part of that question. Bring the bike details and the manual to the person advising you. That is more useful than asking only whether a mudguard is suitable for a road bike, a category that includes many different configurations.

Plan for contact-point care and the rest of the wet-weather kit

SKS includes protective film and cautions about paintwork and carbon surfaces. Its manual calls for cleaning the mounting areas and inspecting the rubber fasteners, which age and need replacement when damaged. A removable fitting is still a contact point on the bicycle. Do not treat the film as a promise that installation and maintenance cannot affect the finish.

Give the mudguards a defined place in your bike-care routine rather than expecting them to replace it. If wet-weather maintenance also means reconsidering chain lubricant, the Finish Line Wet and Dry lubricant guide discusses a different product choice. The fender selection and the lubricant selection should each answer their own intended-use question.

Keep the article number with your instructions so later support questions identify the set precisely. A photograph of the original fitting can be useful when discussing an issue, but it does not replace the checks needed after removal or adjustment. For a shared bike, make sure the person reinstalling the guards knows where the instructions are and understands the clearance requirements.

Order the intended finish and size, not just the family name

This comparison links the shiny-black 11319 standard set and shiny-black 11322 XL set. Matte-black versions have different article numbers, and Raceblade Long is a separate product name. Match the complete model, finish and set description in the selected listing. Shared Raceblade branding is not enough to establish that a different listing is the same item.

Choose the standard Pro when its narrower tire application and shorter profiles match a verified fit. Choose Pro XL when your tires fall in its 25 to 32 mm range and the longer assembly can be fitted correctly. If neither passes the clearance check, neither is the right purchase for that bicycle. The useful outcome is a suitable removable setup, not a universal winner.

Official sources and further reading

Sources reviewed on November 15, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.