Laynie Hasan.

← All offer guides

School & Office Comparisons · Reviewed November 13, 2026

Westcott T-800 vs T-831: Which Circle Template Fits?

For a map key full of tiny symbols, choose the Westcott T-800. For a floor plan with two-inch round tabletops, choose the T-831. Both start at 1/16 inch, but the smaller stencil has some fine sizes its larger sibling skips. The larger one earns its place when a circle wider than an inch actually belongs on the page.

Best for

Students, teachers and illustrators repeating measured circles on paper, especially for map symbols, scale plans and hand-drawn keys.

Probably not for

Cutting discs, checking whether a part meets a machining tolerance, or completing an assignment that requires compass construction.

Specifications at a glance

Manufacturer specifications for the exact versions compared
Drawing decisionWestcott Small Circles T-800Westcott Large and Small Circles T-831
Labeled circle diameters41 sizes, 1/16 to 1 inch45 sizes, 1/16 to 2¼ inches
Detail between 1/16 and 3/32 inchIncludes 5/64 inchGoes from 1/16 to 3/32 inch
A 6-foot table at ¼ inch to 1 footNo 1½-inch openingHas a 1½-inch opening
Rounded rectangle cornersFour named radii: 1/16, 1/8, 1/4 and 3/8 inchChoose this one for larger circles; no equivalent set of corner guides is specified
Placing a circle over a pencil crossTranslucent guide with center marksTranslucent guide with center marks

As an Amazon Associate I earn from qualifying purchases.

Westcott T-800 Small Circles Template

An inch-based stencil for 41 circle diameters up to one inch. It also provides four rounded outside corners that can be traced independently of the holes.

Pros

  • Includes small intermediate diameters such as 5/64 inch
  • Four different corner radii for boxes, cards and keys

Cons

  • Largest complete circle is one inch across
  • A broad writing tip may not make a useful outline through the smallest holes

Who it’s for: Choose it for small diagram symbols, map legends and rounded boxes on notebook pages.

Check Westcott T-800 Small Circles Template on Amazon

Westcott LetterCraft T-831 Large and Small Circles Template

One sheet spans small symbols and circles up to 2¼ inches across. Fraction labels identify the larger openings, including 1½, 1¾ and 2 inches.

Pros

  • One sheet covers scale drawings with both small marks and broad circles
  • Center marks help position concentric rings or align a row

Cons

  • Omits some of the small fractional diameters on the T-800
  • Stops at 2¼ inches, even if there is room on the page for more

Who it’s for: Choose it for classroom layouts or diagrams that regularly call for circles wider than an inch.

Check Westcott LetterCraft T-831 Large and Small Circles Template on Amazon

Why 45 sizes do not replace 41

Look at the first few holes, not just the big circles on the far end. On the T-800, Westcott shows 1/16, 5/64 and 3/32 inch in succession. On the T-831 the first two labels are 1/16 and 3/32. Put those three fractions over a common denominator and the difference is easy to see: one stencil gives you 4/64, 5/64 and 6/64, and the other gives you the two endpoints. The T-831 has more sizes overall, but it is not the T-800 with four extra holes tacked on.

That matters for a mapmaker matching an existing key. If an earlier sheet uses a 5/64-inch open symbol for a spring, the smaller stencil lets the next sheet match. If you are making a new key, you can choose a symbol both guides carry, such as 1/8 inch. In that case neither earns a place in the basket on the strength of an unused fraction. If you are copying a printed original, measure a full-size copy; a handout reduced to fit a page may no longer match its own legend.

Write down just the sizes you need for the next drawing. Check those numbers against the labeled tool in the product photo. A range tells you about the smallest and largest openings, not the steps in between. Also check the unit on a supply list: a decimal printed beside an inch fraction is a decimal inch, not a second set of metric circles. A class that specifies exact millimeter diameters may be better served by a metric template.

Work out the circle on the page

Suppose a class is drawing a school fair at a scale of a quarter inch to one foot. A four-foot round table becomes a one-inch circle. Both stencils have that opening. A six-foot round table becomes a one-and-a-half-inch circle, and an eight-foot round table needs two inches. The T-831 covers all three. A student who already owns a T-800 and has only the four-foot tables on their plan has no reason to change. It is the furniture list together with the drawing scale that makes the purchase worthwhile.

Halve the drawing scale to one-eighth inch per foot and those same tables need half-inch, three-quarter-inch and one-inch outlines. Now all three fit the T-800. Before switching scales just to use a tool you own, make sure the finished drawing still leaves room for labels and that the assignment allows it. A plan intended for other people to interpret should declare its scale. An enlarged photocopy might still show the furniture arrangement, but the rings on that copy will not be the original diameters.

For a nine-foot circular display at the original quarter-inch scale, the T-831 reaches exactly the required 2¼ inches. A ten-foot display needs 2½ inches, beyond either stencil. Tracing two halves of a smaller opening does not fix that; both arcs still belong to the smaller circle. Use a compass set to the required radius. The Staedtler school drawing compass comparison is useful if you are deciding between drawing in graphite and fitting a different marking tool.

Place the center before picking up the pen

Imagine a worksheet with a row of clock faces. Draw one light horizontal guide through the intended centers, then make a short vertical tick for each clock. The lines need to extend far enough to see through the template outside the open hole. Match the upper and lower center marks to the vertical line and the side marks to the horizontal one. Trace, lift and move to the next tick. It is the marks on the worksheet that determine the spacing: the distances between holes on the stencil have nothing to do with the layout.

For an outer ring around each face, keep the center guides until the second circle is complete. Slide the sheet to the new diameter and line up both axes again. Trying to judge an even gap by eye can put a narrow rim on one side and a thick one on the other. Both Westcotts provide center lines, so this job alone does not favor either one. The diameters you want for the face and the rim are what break the tie.

Think about the pen as well as the stencil if those rings will be small. Two broad lines can swallow the white space between them. Try a few rings on a scrap with the same writing tip you intend to use for the finished key, then view them at reading distance. The Sakura Micron 01 and 05 fineliner comparison explains why stroke width changes how a little mark reads. A template labels a nominal diameter; it does not guarantee the outside measurement of every ink line drawn through it.

The useful part with no hole in it

The T-800 has a second job on a sheet of illustrated instructions. Say the arrows and circular step numbers are already down, but the captions need boxes. A square box nearly touches the drawing at each corner. Westcott identifies four corner radii on the T-800, so you can choose a shallow curve, draw a box around the first caption and carry the same curve over to the rest. Use the rounded outside edge for that turn; you need not pick out a quarter of a circle from a tiny hole each time.

A radius is not a diameter. A quarter-inch corner radius follows the curvature of a half-inch-diameter circle, not a quarter-inch circle. If you are matching an existing printed box, lay the guide on a sample corner and look at where the curve meets its two straight sides. Decide on the curve before inking the straight lines all the way to their intersection. On a narrow caption strip there may not be room at both ends for a generous radius and the lettering between them.

Westcott describes the T-831 in terms of its circle diameters and alignment marks. If you need the four specified corner curves, buy the T-800 for that feature. If you need two-inch circles and only an occasional rounded box, a separate corner template may be unnecessary. With the T-831 you can pencil the sides of a box and use part of an appropriate circle to draw the turn. It takes more positioning, which matters more on a page of twenty captions than it does on one title block.

When a tracing guide is the wrong purchase

Check the verb on the assignment. Draw six matching circles for a map legend and either stencil can be useful. Construct the perpendicular bisector of a segment and the arcs you draw from the two endpoints are part of the solution. A traced circle that looks right does not show that construction. Likewise a lesson that asks students to keep the same compass opening while transferring a distance is about carrying the distance, not about discovering which printed fraction nearly matches it.

For classroom supplies, look at one typical completed page before ordering a stencil for each desk. A notebook full of symbols under an inch plus rounded captions points to the T-800. A sheet with several sizes of round tables for a floor plan points to the T-831. If the job is really a stack of cut-paper counters, tracing supplies only the outlines; look for a punch in the finished size instead. Those three projects can all be called making circles on a supply request, yet they call for three different purchases.

Official sources and further reading

Sources reviewed on November 13, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.