Music & Hobby Comparisons · Reviewed November 13, 2026
BOSS FS-5U vs FS-5L: Which Footswitch Fits Your Rig?
For a separate stop button on a BOSS RC-1, buy the silver FS-5U. To change channels on a Katana-50 MkII, buy the black FS-5L. The U releases its switch when you lift your foot; the L holds its setting until your next press. The equipment at the other end of the cable decides which behavior is useful.
Best for
Players adding one external foot control to an amp, looper or effects unit whose manual specifies a momentary or latching switch.
Probably not for
Continuous volume swells, half-damper piano technique, switching a guitar signal between two amps, or sending MIDI commands directly.
Specifications at a glance
| Decision at the pedalboard | FS-5U Un-Latch Footswitch | FS-5L Latch Footswitch |
|---|---|---|
| After a press and release | Returns to its resting state | Retains its new state until another press |
| Identify it in a gig bag | Silver enclosure; no status LED | Black enclosure; LED for switch status |
| Power requirement | No batteries | No batteries needed to switch; two AAA cells for the LED |
| RC-1 external stop | Supported at the STOP/UNDO jack | Explicitly excluded in the RC-1 manual |
| Katana-50 MkII channel selection | Not the switch Roland specifies | One FS-5L on a mono instrument cable selects CH1 or CH2 |
| Cable connection | Quarter-inch phone jack | Quarter-inch phone jack |
As an Amazon Associate I earn from qualifying purchases.
BOSS FS-5U Un-Latch Footswitch, silver
A single momentary contact for gear that reads taps or holds, including the RC-1 external stop input and the MS-3 delay tap assignment.
Pros
- A fresh press and release for each beat of tap tempo
- No battery to pack for a session
Cons
- Cannot maintain a latched contact after you let go
- No indicator to show whether an effect is active
Who it’s for: Buy it when the receiving device specifies an FS-5U or a compatible momentary switch.
Check BOSS FS-5U Un-Latch Footswitch, silver on Amazon Paid linkBOSS FS-5L Latch Footswitch, black
A single latching control with an optional battery-powered indicator. One unit can handle channel selection on the Katana-50 MkII.
Pros
- Keeps its setting without a foot on the pedal
- Still switches if the indicator batteries are removed
Cons
- Not compatible with the RC-1 stop input
- One unit cannot independently select both channel and bank on the Katana-50 MkII
Who it’s for: Buy it for a documented latch input when one maintained on/off choice is enough.
Check BOSS FS-5L Latch Footswitch, black on Amazon Paid linkWhat has to stay on after you lift your foot?
Picture a guitarist playing the last chord of a loop. The backing part must stop, and it must stay stopped while the guitarist walks away. That sounds like a job for a latching switch. On a BOSS RC-1, it is exactly the opposite: the looper needs one brief instruction to stop. The looper remembers that playback has ended. There is no reason for the external switch to keep telling it to stop, any more than someone needs to keep a finger on a pause button.
Now picture the same guitarist moving from a clean verse to a louder chorus on a Katana-50 MkII. On that particular amp, the channel foot control calls for a latching switch. A press on the FS-5L changes the contact and leaves it there, so the guitarist can step back to the microphone. The next press selects the other channel. In both examples the musical change outlasts the footstep. The difference is whether the equipment wants a short command or a contact that stays in position.
Use the model name on the back of the equipment to find its manual, then look for the external footswitch diagram. A jack labeled foot control tells you where to plug in; it does not say which kind to buy. If the diagram names one of these two BOSS models, follow the final letter. A photo that shows a silver or black pedal can help identify something borrowed at rehearsal, but read the model number before counting on it for the set.
A one-press ending for the RC-1
The RC-1 normally lets a player stop a loop with two quick presses on its own pedal. Imagine keeping a four-bar rhythm part going under a solo, then cutting the backing on the first beat of the next verse. With the FS-5U connected to STOP/UNDO as shown in the manual, one short press on the separate switch can stop playback. That leaves the main pedal for its recording and playback jobs. Someone already comfortable landing the double press may prefer to keep the floor space.
One detail matters when arranging the pedals: holding that external stop switch for two seconds or longer can erase the phrase. Put it somewhere you can tap cleanly and lift your foot, not where you naturally rest a boot between cues. Connect the footswitch while the RC-1 is off, as its manual directs, and use a throwaway rhythm for the first run-through. It is worth learning where your foot lands before you have a backing part you would mind losing.
The FS-5L is not an alternative for this setup, even if it is the switch you already own. BOSS explicitly excludes it in the RC-1 manual. Nor does adding an FS-5U add recording memories: if the real problem is getting a different prepared backing part ready for each song, the BOSS RC-1 and RC-5 looper comparison explains what the looper itself needs to provide. An easier ending and more places to save songs are separate purchases.
A channel button is not a bank button
On the Katana-50 MkII, Roland specifies one FS-5L with a standard quarter-inch mono instrument cable for changing between CH1 and CH2. Suppose you save a rhythm sound to channel one and a lead sound to channel two in the same bank. The single FS-5L covers both transitions in that song. There is no need to buy a second switch just because two sounds are involved; the one button alternates between those two channels.
The count changes when the next song uses a different bank and you want to recall that from the floor as well. There are now two independent choices: which bank, and which channel within it. Roland documents a two-FS-5L arrangement using an insert cable. Two mono quarter-inch plugs go to the switches and a single stereo quarter-inch plug goes to the amp. A second identical guitar cable by itself will not do the job. A headphone splitter that duplicates one signal is not the specified insert cable either.
Write the four sounds down as A1, A2, B1 and B2 before ordering hardware. If a hand change between songs is fine, a single switch may still be enough. If you need to move between banks midway through a song, budget the second control and its cable, or consider a compatible dual controller. These examples apply to the Katana-50 MkII named here; a listing that just says Katana is not evidence that every generation and variant takes the same controller.
Tapping a delay without changing patches
On the BOSS MS-3, the useful accessory for delay tap tempo is the FS-5U. Think of a band starting the chorus a touch faster than the studio recording. You want to mark the spacing between beats, not leave a switch on for the duration of the chorus. The MS-3 can interpret successive presses from the FS-5U as a tempo when its external control is assigned to delay tap. Once you have tapped the beat, the delay keeps its timing without your foot holding anything down.
Buying the right switch does not make that assignment automatically. Roland’s MS-3 example uses a mono instrument cable to the EXP1/CTL 1/2 input, a momentary delay-tap assignment and an enabled delay effect. The settings are saved to a user patch. If the switch works on the rehearsal patch but not on the patch for the next song, compare those assignments before blaming the cable. If the aim is to sweep a parameter smoothly from one value to another, neither the U nor the L supplies the intermediate positions.
Read the light as a switch indicator
The FS-5L can change a channel without batteries. Two AAA cells power its indicator, not the latching action. This is useful if the amp is out of your line of sight: with the indicator available, step through the two sounds at rehearsal and note which sound corresponds to the lit position. The lamp reports a switch state. It cannot tell you whether channel two contains your intended solo patch or the sound someone saved there yesterday.
If the light is dark but the channels still alternate, check the batteries before replacing a working switch. If the light changes but the sound does not, look instead at the destination jack, the cable and the two stored sounds. And if the intended job is at a digital piano, ask what the sustain input needs. A switch can request full sustain on compatible gear; it cannot measure a partial pedal stroke. The Yamaha FC3A and FC5 sustain pedal comparison is a better starting point for choosing between half-pedaling and simple on/off sustain.
Official sources and further reading
Sources reviewed on November 13, 2026. Prices, availability and terms can change; recheck before buying.
- BOSS: FS-5U and FS-5L switch types, colors, connectors and battery specifications
- BOSS RC-1 owner’s manual: external stop, erase, polarity and connection precautions
- Roland support: Katana-50 MkII channel and bank switching and cable choices
- Roland support: assigning the FS-5U to delay tap tempo on the MS-3
- Roland support: operating the FS-5L with or without indicator batteries
- Amazon US: BOSS FS-5U Un-Latch Footswitch Paid link
- Amazon US: BOSS FS-5L Footswitch for ON/OFF Control Paid link
Commission disclaimer
This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.