Music & Hobby Comparisons · Reviewed November 5, 2026
D’Addario Pro-Winder vs Peg Winder: Do You Need Cutters?
Buy the black Pro-Winder if you want a single tool in your guitar case for winding strings, lifting bridge pins and clipping wire. Choose the Ergonomic Guitar Peg Winder if your string cutters already live where you change strings. You do not have to buy the Pro to get a pin puller. Both have one, and on a guitar with a pinless bridge you can leave it alone.
Best for
A guitarist changing steel strings at home or at rehearsal who wants to turn conventional tuning keys with a hand crank.
Probably not for
Someone looking for a pitch display, a powered winder or the larger bass-specific version of either tool.
Specifications at a glance
| String-change task | Pro-Winder for guitar | Ergonomic Guitar Peg Winder |
|---|---|---|
| Selected model | DP0002, black | PWPW1, Guitar selection |
| Turn a tuning key | Manual crank | Manual crank |
| Lift acoustic bridge pins | Integrated puller | Integrated puller |
| Trim steel strings | Built-in hardened steel cutter | Separate string cutter needed |
| Separate bass model | DP0002B | PWPW1B |
As an Amazon Associate I earn from qualifying purchases.
D’Addario Pro-Winder for guitar, black (DP0002)
The extra part you get on the Pro is a pair of cutting jaws. At an open mic, you could replace a broken high E and trim the end before handing the guitar to the next player. Nobody has to go looking for the wire cutters that usually sit on your desk.
Pros
- One item to pack for winding, pulling pins and trimming wire
- Cutter is available for an electric guitar even when its bridge has no pins
Cons
- Duplicates a cutter you may already prefer
- Cannot leave the cutting jaws at home while taking just the crank
Who it’s for: Pick the Pro for a guitar that leaves the house. The reason to pass is a complete tool roll that already goes with it.
Check D’Addario Pro-Winder for guitar, black (DP0002) on Amazon Paid linkD’Addario Ergonomic Guitar Peg Winder (PWPW1)
The molded Peg Winder keeps the crank and acoustic pin puller together but leaves the clipping to you. At a teaching bench you can hand a student the crank, keep the cutters on your side of the table and show the winding and trimming steps separately.
Pros
- Adds a pin puller without duplicating your string cutters
- Lets you choose the cutters independently of the crank
Cons
- Leaves a loose wire end to deal with if you forget your cutters
- Easy to confuse the Guitar selection with the separately listed Bass Guitar model
Who it’s for: Pick it for an equipped bench or a case with cutters inside. Skip it for a one-tool kit intended to handle steel-string changes away from home.
Check D’Addario Ergonomic Guitar Peg Winder (PWPW1) on Amazon Paid linkStart at the bridge, not the tuning key
Look at the end of the strings farthest from the tuners. On a conventional pin-bridge acoustic, six small pin heads sit behind the saddle. With the old string slack, the puller helps lift its pin so the ball end can come out. The crank does a different job at the opposite end of the guitar. It turns the button you normally turn with your fingers. Owning a pin bridge gives you a reason to want a puller, but does not favor one of these models over the other.
On the way back in, the puller has no job. Taylor’s steel-string instructions show the new ball end going in first, followed by the pin. Draw the string up gently to seat the ball before winding at the headstock. If the pin starts to rise as you take up slack, stop and check how the string is seated. Turning faster or pressing a pin into place with a tool is not the answer. For an electric guitar that feeds through a tailpiece instead, follow that string path; there is no acoustic pin to lift.
When should the cutters come out?
A useful question on a first string change is whether to cut the new string before or after winding. It depends on the installation you are following. Taylor’s instructions for its conventional steel-string headstock measure extra length beyond the intended post and trim before insertion. D’Addario’s illustrated electric guitar method bends the string to mark the allowance, winds it onto the post and then clips the excess. Either tool can crank the post in either example. What changes is the moment you need access to the jaws.
Before the first cut, point to the post the new string belongs on and trace the string back to its bridge position. On a three-per-side headstock, a few inches of wire from several strings can all be pointing in different directions. Isolate the one free tail you mean to clip. Hold the portion you are discarding so a sharp offcut does not land in the case lining. If you are removing an intact old string, loosen it first; there is no need to cut across a string at playing tension.
What the crank can tell you, and what it cannot
Rest the guitar securely and seat the winder on one tuner button before moving the handle. Try a short turn and watch both the intended post and the neighboring buttons for clearance. Pluck the old string as you start to loosen it. If its pitch rises, reverse direction; if a different string changes, you are on the wrong key. This check is worth more than memorizing a direction from a photograph taken from the other side of the guitar.
When the new string starts to hold a note, take the crank off and make the last adjustments by hand. It is easier to make a small correction that way, and neither winder gives you a reading. If the display you use is awkward to see while holding the key, the Micro vs Eclipse clip-on tuner comparison shows two ways to position it. If you can already see your tuner, nothing about a new winder calls for replacing it.
Pack for the guitar you actually bring
Picture two cases by the door: a steel-string acoustic for rehearsal and an electric for lessons. You own a good pair of string cutters, but they live in the electric case. Putting a PWPW1 in the acoustic case would give that guitar a crank and a puller, but no cutter when it travels alone. Put the Pro there, or keep your existing cutters and a regular winder together in a pouch that changes cases with you.
A spare string matters more than either tool when one breaks. Keep the packet with the guitar it fits, especially if you move between instruments. If the acoustic already suits light 12 to 53 strings, the EJ16 vs EJ11 acoustic string guide shows how to keep the six gauges the same while changing the wrap material. To order the crank, check the letters as carefully as the strings: PWPW1 is the guitar Peg Winder, not PWPW1B for bass. For the black guitar Pro-Winder, look for DP0002 without a trailing B.
Official sources and further reading
Sources reviewed on November 5, 2026. Prices, availability and terms can change; recheck before buying.
- D’Addario: black guitar Pro-Winder DP0002, integrated pin puller and hardened steel cutting jaws
- D’Addario: Guitar option PWPW1, molded winder and integrated acoustic pin puller
- D’Addario: separate DP0002B bass model
- D’Addario: compare the Guitar and Bass Guitar selections before ordering
- Taylor Guitars: seating a ball end and measuring string length before winding
- D’Addario: electric guitar tailpiece, winding and trimming the free end
- Amazon US: black DP0002 guitar Pro-Winder, one tool Paid link
- Amazon US: Ergonomic Guitar Peg Winder, model PWPW1 Paid link
Commission disclaimer
This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.