Safety Equipment Comparisons · Reviewed October 15, 2026
DEWALT DPG82-11 vs 3M GG501SGAF Safety Goggles
Both are low-profile, indirect-vent clear goggles with anti-fog coatings. DEWALT uses a dual-injected rubber seal; 3M documents D3 splash and D4 dust ratings, disassembly and an optional prescription insert.
Best for
Trained workplace buyers comparing two exact indirect-vent clear goggle models after a hazard assessment identifies the required eye protection.
Probably not for
Medical advice, sports, lasers, welding, firefighting, chemical-specific approval, respiratory protection or selecting PPE without current employer and manufacturer requirements.
Specifications at a glance
| Detail | DEWALT DPG82-11 | 3M GG501SGAF |
|---|---|---|
| Lens | Clear polycarbonate | Clear polycarbonate |
| Coating | Anti-fog hard coat | Scotchgard anti-fog / anti-scratch coating |
| Venting | Ventilation channels / indirect design | Indirect ventilation |
| Face interface | Soft dual-injected rubber seal | Low-profile flexible goggle body with wide nose area |
| Strap | Adjustable elastic cloth strap | Adjustable elastic cloth strap; removable |
| Published standard | Meets ANSI Z87.1 impact-protection standard | Meets ANSI-ISEA Z87.1-2020 impact-rated protector requirement |
| Additional rating | No D3 or D4 marking stated on cited DPG82 page | D3 droplet and splash; D4 dust |
| Service features | No replacement lens or insert stated on cited page | Disassembles for cleaning; replacement lens and optional prescription insert available |
| Exact model | DPG82-11 / part DPG82-11C | GG501SGAF, 3M ID 7100079187 |
As an Amazon Associate I earn from qualifying purchases.
DEWALT Concealer Clear Anti-Fog Safety Goggle (DPG82-11)
A clear-lens goggle with a soft dual-injected rubber face seal, ventilation channels, adjustable cloth strap and anti-fog hard coat. The maker states ANSI Z87.1 impact protection and 99 percent UV protection.
Pros
- Dual-injected rubber seal is the clearest design distinction
- Simple one-piece product identity is widely documented as DPG82-11
- Adjustable cloth strap and ventilation channels are published
Cons
- Cited maker page does not state D3 splash or D4 dust markings
- No optional prescription insert or replacement lens is documented there
- Amazon uses DPG82-11, DPG82-11C and DPG82-11CTR notation for the clear variant
Who it’s for: Choose only when the exact DPG82-11 markings and instructions meet the completed hazard assessment. Skip it when the task requires a rating or compatibility feature not shown on its current documentation.
Check DEWALT Concealer Clear Anti-Fog Safety Goggle (DPG82-11) on Amazon Paid link3M GoggleGear 500 Clear Scotchgard Goggle (GG501SGAF)
A low-profile clear polycarbonate goggle with indirect vents, adjustable removable cloth strap and Scotchgard anti-fog/anti-scratch coating. 3M states D3, D4 and ANSI-ISEA Z87.1-2020 impact-rated protector qualifications.
Pros
- D3 splash and D4 dust ratings are explicitly documented
- Lens, frame and strap disassemble for cleaning
- Replacement lens and optional prescription insert are supported
Cons
- 3M labels this industrial and occupational PPE for trained workplace customers
- Low-profile shape and insert availability do not guarantee fit with every face or respirator
- Amazon package quantity must be checked against the exact listing and part number
Who it’s for: Choose only when GG501SGAF ratings, markings, fit and workplace program requirements match the hazard. Skip it for consumer, school, sport or other use outside 3M labeling.
Check 3M GoggleGear 500 Clear Scotchgard Goggle (GG501SGAF) on Amazon Paid linkA hazard assessment comes before brand comparison
Safety goggles are selected for a defined exposure, not as a generic upgrade from ordinary glasses. Identify impact, liquid splash, droplet, dust, optical radiation and chemical hazards with the responsible employer or safety professional. Then match every required marking to the exact product and current instructions. A familiar tool brand, clear lens or anti-fog label does not establish suitability for a substance, process or workplace.
This comparison covers DEWALT DPG82-11 and 3M GG501SGAF only. It does not approve either product for welding, lasers, firefighting, sports, medical use or a particular chemical. 3M expressly describes GG501SGAF as industrial and occupational PPE for trained workplace customers. Applicable OSHA rules, ANSI requirements, site policy and the manufacturer's limitations remain controlling.
The seal and nose geometry determine whether protection is continuous
DEWALT uses a soft dual-injected rubber seal intended to conform around the face. 3M uses a low-profile body with a wide flexible nose area and advertises compatibility with some half-mask respirator arrangements. Neither description guarantees a seal on an individual wearer. Facial shape, hair, eyewear, headwear and other PPE can create gaps or pressure points.
Inspect contact around the entire perimeter while making normal head movements. The strap should hold the goggle in position without distorting the frame. If a respirator, hard hat or hearing protector is also required, evaluate the complete ensemble under the workplace program. Do not trim the seal, punch vents or substitute straps; modifications can invalidate protection and certification.
Indirect ventilation balances airflow with defined coverage
Both exact models use ventilation paths rather than a fully open spectacle frame. DEWALT describes ventilation channels, while 3M specifies indirect ventilation. Indirect vents can reduce direct entry paths while allowing air exchange, but they are not equivalent to an unvented goggle. The correct vent type depends on the hazard assessment and product markings, not on which design feels cooler.
3M explicitly lists GG501SGAF as D3 for droplet and splash and D4 for dust. The cited DEWALT product page states protection from dust and debris but does not publish those same D3 and D4 designations. Do not translate descriptive language into a standard marking. If a procurement specification requires D3 or D4, verify the marking on the exact goggle and its current documentation before purchase.
Anti-fog coatings reduce a problem but do not eliminate it
DEWALT uses an anti-fog hard coat intended to help with fogging and scratches. 3M uses Scotchgard anti-fog and anti-scratch coating and publishes an internal EN168-based comparison against traditional coatings. Those claims were not produced by a shared head-to-head test, so this guide does not rank fog resistance or scratch life between the two exact goggles.
Humidity, exertion, temperature change, cleaning residue and interaction with a respirator can still fog either lens. Follow only the approved cleaning method because household glass cleaners, abrasives and solvents can damage polycarbonate or coatings. Replace a lens that stays cloudy, is deeply scratched or prevents a clear view. Do not continue hazardous work through obstructed vision.
Standards must be read from the exact model and marking
Radians, the manufacturer of the DEWALT-licensed goggle, states that DPG82 meets ANSI Z87.1 for impact protection and provides 99 percent UV protection. 3M states that GG501SGAF meets the impact-rated protector requirement of ANSI-ISEA Z87.1-2020 and lists D3 and D4 ratings. These statements apply to the exact documented configurations, not every lens color or similarly named family member.
Check the permanent lens and frame markings when the product arrives and compare them with the current user instructions and procurement requirement. Standards have editions and marking conventions, and a marketplace title can omit critical details. UV language also does not make clear safety goggles appropriate for welding or lasers. Those hazards require specifically rated filters selected for the source and operation.
Cleaning and prescription support differ
3M states that the GG501SGAF lens, frame and strap can be quickly disassembled for cleaning. It also offers a replacement lens and optional prescription insert. That can support a managed PPE program, but only approved components preserve the specified configuration. Confirm insert model, prescription workflow and compatibility through 3M or the safety program rather than wearing ordinary glasses underneath without evaluation.
The cited DEWALT DPG82 page does not list a replacement lens or prescription insert. Clean it as directed and replace the goggle if required components are damaged or unavailable. Inspect straps for loss of elasticity, vents for blockage, the seal for cracks and lenses for distortion before each use. Sharing goggles also requires a hygiene and disinfection process that does not harm materials.
Choose only after markings, fit and the PPE program agree
Choose DEWALT DPG82-11 when its exact markings, dual-injected seal, ventilation and clear lens satisfy the completed assessment and individual fit check. Choose 3M GG501SGAF when its documented D3, D4 and ANSI-ISEA Z87.1-2020 qualifications, removable strap and service components match the program. Neither is a universal winner, and neither should be selected solely for comfort or appearance.
The verified Amazon ASINs are B01A12J3GI for the clear DEWALT DPG82-11 variant and B016L26QS0 for 3M GG501SGAF. Confirm the full model, clear lens, standard markings and package quantity before ordering. No price, stock, medical outcome, chemical compatibility, fog-duration result, fit guarantee or personal-use claim is made.
Official sources and further reading
Sources reviewed on October 15, 2026. Prices, availability and terms can change; recheck before buying.
- DEWALT: current DPG82 product identity and Concealer family specifications
- Radians: DPG82 seal, coating, strap, venting, ANSI and UV specifications
- 3M: current GG501SGAF part identity, lens, venting, strap, D3, D4 and ANSI-ISEA specifications
- 3M: disassembly, replacement support, prescription insert and lens specifications
- Amazon: exact DEWALT DPG82-11 clear goggle listing and ASIN identity
- Amazon: exact 3M GG501SGAF clear goggle listing and ASIN identity
Commission disclaimer
This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.