Laynie Hasan.

← All offer guides

Sewing & Craft Comparisons · Reviewed November 11, 2026

Dritz 562 Tailor’s Ham vs 561 Seam Roll for Sewing

A sleeve can need both shapes, but not in the same place. The Dritz 562 ham supports the rounded shoulder at the top. The long 561 roll slips inside the sleeve to put the underarm seam under the iron without pressing the other side of the sleeve flat.

Best for

Garment makers choosing a first pressing form for bodice darts, curved jacket seams, sleeve seams or trouser alterations.

Probably not for

Measuring hem depth, setting a full-length trouser crease, correcting a misplaced dart or pressing fabric whose care instructions rule out ironing.

Specifications at a glance

Manufacturer specifications for the exact versions compared
What to compareDritz 562 tailor’s hamDritz 561 seam roll
Working surfaceRounded body with a narrower endLong, narrow body with a rounded cross section
Garment area it supportsThe fullness around a dart, collar or sleeve capOne length of seam inside a sleeve or trouser leg
Plaid face, per Prym65% cotton and 35% polyester; low to medium heat65% cotton and 35% polyester; low to medium heat
Other face, per Prym100% cotton; medium to high heat100% cotton; medium to high heat
Main limitWidth can keep it out of a narrow tubeNarrow crown gives little support to a broad, rounded panel

As an Amazon Associate I earn from qualifying purchases.

Dritz 562 Tailor’s Ham for Pressing and Molding

A shaped pressing cushion for fabric that should keep its curve when the iron lifts. Turn it until the fabric beyond the seam rests on the form without folding.

Pros

  • Different parts of the form suit shallower or steeper curves
  • Supports the unstitched fabric around a dart point as well as the dart itself

Cons

  • Its broad body limits access inside a finished narrow sleeve
  • A long straight seam needs frequent repositioning

Who it’s for: Choose the 562 for fitted bodices, waist darts, curved collars and the shoulder ends of set-in sleeves.

Check Dritz 562 Tailor’s Ham for Pressing and Molding on Amazon

Dritz 561 Seam Roll for Pressing Seams

An elongated pressing cushion. Lay the stitch line along its crown so the iron reaches that line while the fabric on either side drops away.

Pros

  • Fits into garment openings that will not admit a broad ham
  • Separates the two walls of a sleeve or leg while you press one seam

Cons

  • Cannot be assumed to fit every cuff or child-size sleeve
  • Provides less support than the ham around the point of a bodice dart

Who it’s for: Choose the 561 when opening underarm seams, pressing trouser side seams or working inside an alteration you cannot lay out flat.

Check Dritz 561 Seam Roll for Pressing Seams on Amazon

What a flat board misses at the point of a dart

Sew a waist dart in a skirt front and the piece no longer wants to lie flat. The two marked dart legs have met, taking up a wedge at the waist and leaving room over the hip. If you spread the skirt on a board and pull until the whole front touches it, a fold has to appear somewhere. That fold is exactly what you do not want to catch under the iron. Give the hip room to rise. The 562 does its best work under that newly rounded part, not just under the thickest bit of stitching.

Lay the skirt over the ham with the wrong side facing you. Before picking up the iron, turn the form until the cloth lies quietly on both sides of the dart point. Fold the dart allowance in the direction the pattern specifies. Work toward the point with a lifting motion, then look at the right side over the form. The test is not whether the whole panel lies flat afterward. Look for a smooth transition from the stitched dart to the unstitched curve, without a little pressed line continuing past the point.

A point that sits in the wrong place on your body is a different problem. Try on the garment or its test version before committing to the final press. If the dart needs to end higher, lower or farther from the fullest part of the hip, change the stitching or the pattern. The comparison of Nancy Zieman’s and Sarah Veblen’s fitting books is more relevant to that decision than a second pressing cushion.

The underarm seam is a different job from the sleeve cap

Picture an ordinary shirt sleeve sewn into a tube but not yet attached to the shirt. You need to open the underarm seam. Lay the sleeve flat on the board and you can reach the seam, but there is a second layer of sleeve directly beneath it. Slide the 561 inside instead, from the wider opening if necessary. Bring the underarm stitching up to the top of the roll. Now the far wall of the sleeve wraps underneath, out of the path of the iron. You can open the allowances without deliberately creasing the center of the sleeve.

If the sleeve is longer than the roll, press the length it supports, lift the iron, and draw the next section into place. Check which seam is actually on top before continuing. A sleeve can turn as it moves, especially once a placket makes one side heavier. Do not force the roll through a buttoned cuff. Open the cuff or approach from the armhole when construction allows. For a very small sleeve, plan to press as much as possible before closing it rather than counting on either tool to fit later.

At the shoulder end, the aim changes. The sleeve cap is meant to round over the shoulder, not resemble a section of straight pipe. Set that part over the end of the ham, letting the rest of the sleeve hang free. Follow the pattern for the direction of the allowances. A stray tuck caught in the seam is worth unpicking; trying to flatten it with more pressure sacrifices the surrounding curve without releasing the cloth caught by the stitches.

Read the marks on a trouser seam

There are two different lines you might see after pressing trousers. One is the intentional crease down the middle of the leg. The other is a faint track running parallel to a side seam, about one seam allowance away from the stitching. The second can appear when the cut edge underneath gets pressed into the outer cloth. The 561 is useful for the second problem: center the stitching on its rounded top and let the allowance edges fall away from the firmest contact. Keep the iron over the seam instead of sweeping its whole width around the roll.

For an alteration, think about when the seam is still accessible. Suppose you are taking in a trouser leg and turning up the hem. Once the fit is settled and the new seam stitched, open it over the roll before turning the hem allowance back up. You can reach the last stretch near the ankle without pushing through all the folded hem layers. Switch to a board when the task is setting a sharp center crease; the narrow support that keeps most of the leg away from the iron is the wrong surface for aligning two long folds.

The cover fabric does not set the iron temperature

Prym’s current specifications for both Dritz items describe a plaid face made of 65% cotton and 35% polyester, and a reverse of 100% cotton. Prym assigns the plaid face to lower or medium heat, including work on woolens, and the all-cotton face to medium or higher heat. A reference to wool in a retail title is not the same as a statement that the cover is wool. Follow the care and use label on the actual item. The garment fabric, lining, interfacing and trims must also tolerate whatever heat you choose.

Before pressing a dark jacket front, sew a short sample seam from the same fabric and put the same layers underneath it. Try the intended face of the cushion, the iron setting and a suitable press cloth. Let the sample cool, then tilt it toward the light. A glossy patch where the iron touched and a raised line where an allowance ended call for different changes. Protect the surface and revisit heat or pressure for shine; for an edge showing through, reposition the allowance off the crown. Do not raise the temperature to solve either problem.

Which form earns a place next to your iron?

Look at the construction order of the next garment you actually plan to sew. A sleeveless sheath with waist darts and curved bodice seams offers the ham a job before you even reach the side seams. For someone altering several pairs of trousers, the roll is likely to be useful each time a leg seam has to be opened inside a finished tube. If you make both, start with the step that stops your work on the flat board. It is reasonable to own just the ham if most of your straight seams are still accessible before the garment is assembled.

Flat patchwork blocks and a straight curtain hem usually need neither shape. A board can support the entire block; a measuring edge is what sets the depth of a repeated fold. See the Clover Hot Hemmer and Hot Ruler comparison if keeping an even turn-up is the problem. A pressing form answers a different question: what should be underneath this particular piece of fabric when the iron comes down? For the fullness at a dart, choose the ham. For a stitch line inside a tube, choose the roll.

Official sources and further reading

Sources reviewed on November 11, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.