Laynie Hasan.

← All offer guides

Tools & Workshop Comparisons · Reviewed November 8, 2026

Kreg 310 vs 320: When Are Two Drill Guides Useful?

The Kreg 320 does not drill a deeper joint than the 310. It gives you a second drill guide and a removable spacer, so you can drill a planned pair of holes without moving a single guide between marks. Both jigs cover the same stock thicknesses. For occasional holes in different locations, the 310 is enough; for a stack of matching frame parts, the 320 gives you a pattern worth repeating.

Best for

A woodworker choosing a portable jig to clamp to a board or panel, with a drill already available and a project that calls for pocket-hole screws.

Probably not for

Someone expecting a self-clamping bench machine, a jig for shelf-pin holes, or a specified load rating for an entire finished assembly.

Specifications at a glance

Manufacturer specifications for the exact versions compared
Kit detailPocket-Hole Jig 310Pocket-Hole Jig 320
Kreg item numberKPHJ310KPHJ320
Guides in the standard kitOne drill guide with thickness stopTwo drill guides with thickness stops and a removable spacer
Supported stock thickness1/2 to 1 1/2 inches1/2 to 1 1/2 inches
Marked thickness stops1/2, 3/4 and 1 1/2 inches1/2, 3/4 and 1 1/2 inches
Drilling and driving accessoriesStepped bit, stop collar, thickness gauge/hex wrench and 6-inch square-drive bitSame types of bit, collar, gauge/wrench and driver
Storage and screws on Kreg’s kit listNo case or screws listedCarrying case and 40 sample screws

As an Amazon Associate I earn from qualifying purchases.

Kreg Pocket-Hole Jig 310, KPHJ310

One hardened-steel guide determines the drilling path. Move the jig to the next mark when you need another pocket. That suits a job where the best location for each screw matters more than repeating a particular pair of holes.

Pros

  • Single guide can be positioned independently at every mark
  • Same rated material range as the two-guide kit

Cons

  • Making a pair requires positioning and securing the guide again
  • Standard kit inventory does not list a carrying case or sample screws

Who it’s for: Choose for an occasional repair or widely separated holes. Skip the single-guide format if the next project involves a pile of identical rails with the same two-hole layout.

Check Kreg Pocket-Hole Jig 310, KPHJ310 on Amazon

Kreg Pocket-Hole Jig 320, KPHJ320

Two guide modules work together, with or without the supplied spacer between them. They also separate, so the 320 can be used one guide at a time when a paired layout would put a screw in the wrong place.

Pros

  • Drill a matching pair in one jig position when the spacing suits the piece
  • Includes a case for keeping the gauge, driver and guide modules together

Cons

  • The joined guides still have to be moved along a long panel
  • The supplied spacer is not a continuously adjustable spacing scale

Who it’s for: Choose for repeated two-hole ends or a mix of single and paired placements. Do not buy it for thicker material: its capacity is the same as the 310.

Check Kreg Pocket-Hole Jig 320, KPHJ320 on Amazon

Pencil in the pockets before choosing the jig

Draw the joint as it will look from the back. On a cabinet face frame, for example, the ends of the horizontal rails meet the long edges of the uprights. Mark the back of each rail and sketch the pockets there. Will every rail end use the same pair of holes? If so, the second guide in the 320 has a specific job. You can carry the pair from end to end instead of deciding afresh where the second opening goes on every part.

For a different project, picture adding a single divider inside a box. There may be a groove for the back, a nearby fastener or a narrow strip of clear wood where a screw can go. Two holes at the jig’s paired spacing may put one directly over the groove. The useful feature here is being able to place one guide exactly where the drawing permits. The 310 does that without another module; the 320 can do it after separation. More guides do not give you permission to ignore the joint layout.

Mark the show face too. A pocket on the underside of a shelf may disappear after installation while one on the inside face of an open display cabinet may remain visible at eye level. A plug or a different joint can be a better design decision than buying a larger jig. Neither package changes which face receives the pocket.

Count jig placements, not holes per project

Suppose your design calls for four matching rails, each with a two-pocket joint at both ends. That is eight ends and sixteen holes. If the selected 320 layout fits those rails, eight placements of the paired guides cover the plan. With the 310, the corresponding sixteen holes need sixteen guide placements. The drill still makes sixteen holes either way. This is a count of setup steps for that example, not a claim about how many minutes either tool saves.

Change the drawing to a shelf whose pockets are deliberately spread out along a long edge. Neither pair of adjacent guide holes represents that full layout. Mark the project’s required positions on the stock and move the guide along the marks. Owning the double guide does not turn it into a fence that indexes the next position down the board. The single guide is a reasonable choice when each planned hole already requires a move.

The spacer in the 320 belongs between its guide modules. It changes the separation of their drilling paths; it does not set the depth of the pocket. Kreg’s manual illustrates different configurations for different board widths. Lay the assembled guides against a scrap cut to the rail width before committing to the layout. If their positions do not suit the design, choose another configuration or mark and drill the holes individually.

Width is a layout decision; thickness is a setup decision

Take two offcuts, one narrow and one wide, both cut from the same sheet. Their widths may call for different hole positions while their thickness calls for the same jig and collar settings. Now keep the width constant and substitute a thicker board. Revisit the bit collar and thickness stop even if the two holes should still be the same distance apart. Treating these as independent decisions prevents the common mistake of changing the guide spacing and assuming the depth has changed with it.

Use the supplied material gauge on an actual offcut of the piece being drilled. Kreg lists stock from half an inch through one and a half inches for both jigs, with three marked stop settings. Follow the gauge and manual rather than treating the nominal name on a board label as a measurement. If joining pieces of different thicknesses, consult Kreg’s project-specific screw guidance before drilling. A screw must enter the mating piece without emerging through its visible face. The sample screws in the 320 case are not a project specification.

Make the first joint in scrap from both parts, not merely a spare hole in any piece of wood. That gives you a way to inspect the pocket, check the joint orientation and confirm the chosen screw before repeating the layout across finished work. A change in stock, coating choice for the screws or intended use can justify a new check. Neither jig alone establishes what load a finished shelf, seat or frame can support.

Leave room for both the clamp and the driver

Walk through the job with the drill switched off. First, the jig must register on the intended edge and be clamped securely with the chip exit unobstructed. Second, after drilling, the workpieces must be aligned and held while the screw is driven. Kreg’s manual treats these as separate clamping operations. Holding the jig to a loose rail is not the same as keeping the rail flush with its neighbor during assembly. The anti-slip surface is no substitute for securing the jig.

Check whether a clamp jaw can reach the intended spot and seat properly on both sides. A long clamp hanging off a short piece can be awkward even when its opening is ample. If you are comparing clamps as a separate purchase, the DeWalt vs Irwin trigger clamp guide covers reach and handling; it is not a guarantee that a particular pad fits a Kreg adapter. A clamp adapter and a complete clamp are different items. Look at the exact kit number before counting on either a clamp or a drill being in the box.

An assembled cabinet introduces a different clearance problem. Even if a single guide fits in the corner, is there space behind the stepped bit for the drill? Later, can the driver approach the screw in line with the pocket? The 6-inch driver included with these kits takes up space before the drill body even enters the picture. The DeWalt and Makita drill kit comparison is relevant if you also need a drill. For a repair, try the layout with the actual tools available before choosing either jig.

Compare the standard boxes, not the bundle photos

Look for KPHJ310 if you want the single-guide kit or KPHJ320 if you want two guides and the spacer. A photograph of a clamp holding a jig demonstrates use, not necessarily the contents of the selected box. The same applies to a drill, extra screws or a larger workstation pictured on the page. Inventory the joint-making essentials you already own, then read the parts list for the exact selected package.

The simplest decision is to place one representative piece on the bench. Two holes that belong at one of the paired spacings, repeated on multiple ends, make a good case for the 320. Mostly independent marks favor the 310. If the material is outside the published range, there is no room to clamp safely, or the plan calls for another kind of joinery, neither of these portable jigs solves that problem.

Official sources and further reading

Sources reviewed on November 8, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.