Laynie Hasan.

← All offer guides

Workshop Tool Comparisons · Reviewed November 9, 2026

Kreg vs Milescraft: Which 35 mm Concealed Hinge Jig?

If you are replacing doors on a cabinet and keeping its mounting plates, the Kreg KHI-HINGE lets you work directly from the old hinge centerlines. For new doors and an unmarked cabinet, the Milescraft 1342 adds a detachable marking guide and a choice of two end stops. The first thing to find on the hinge drawing is the gap between the door edge and the cup hole. It can settle the choice before you even measure the cabinet.

Best for

Boring blind 35 mm cup holes in undrilled cabinet doors with a handheld drill, after choosing concealed hinges and confirming the door material and thickness suit them.

Probably not for

Mortising flat butt hinges, repairing torn-out cup holes, or hanging a pre-bored replacement door whose existing holes already match the hardware.

Specifications at a glance

Manufacturer specifications for the exact versions compared
What you set at the benchKreg KHI-HINGEMilescraft 1342 EuroHingeJig
Cup diameter35 mm35 mm
Cup-to-edge offset settings3, 4, 5 or 6 mm2.5, 3, 4, 5, 6 or 7 mm
Location along the hinge edgeScale or marked centerline; at least 2 inches from the endEnd locator pin at 3 or 4 inches; scale for layout
Cup-depth setupStop collar seats on shoulder of the Kreg bitBuilt-in fixtures for 12.7 or 13 mm
Pilot bit for screw holes1/16-inch bit required, sold separately1/16-inch bit included
Locating the cabinet-side plateUse the hinge instructions for the cabinet layoutDetachable marking guide for wall or face frame

As an Amazon Associate I earn from qualifying purchases.

Kreg KHI-HINGE Concealed Hinge Jig

A complete jig with a 35 mm boring bit, two edge cams and a scale that lines up with a pencil mark. The shoulder on its bit gives the stop collar a defined seat.

Pros

  • Centerline marks work for existing plate locations, including a middle hinge
  • No separate depth fixture to choose when assembling the supplied bit

Cons

  • Edge cams do not cover a 2.5 or 7 mm cup offset
  • Requires two clamps and a separate 1/16-inch pilot bit for the guided screw holes

Who it’s for: A good match for replacement doors when you already know the hinge positions, the hinge accepts the jig setup, and you have clamps and a pilot bit.

Check Kreg KHI-HINGE Concealed Hinge Jig on Amazon

Milescraft 1342 EuroHingeJig

A complete 35 mm cup jig with six edge offsets, a removable end locator pin and a guide that carries the hinge centerline over to the cabinet. A pilot bit stores in the jig.

Pros

  • Includes both the 2.5 mm and 7 mm edge settings
  • Pin repeats 3- or 4-inch end locations; removable guide helps mark new mounting plates

Cons

  • Neither end-pin position directly locates a 3.5-inch hinge center
  • Two built-in depth settings still need to be checked against the particular hinge

Who it’s for: Choose it when laying out both sides of a new installation, or when its extra edge settings are a specific requirement. The pin is less useful for a cabinet with oddly positioned existing plates.

Check Milescraft 1342 EuroHingeJig on Amazon

Start with the drawing, not the overlay on the box

A half-inch overlay is not an instruction to put half an inch of wood between the hinge hole and the door edge. Overlay describes how far a closed door covers the cabinet frame or side. Cup offset describes the narrow strip of door material left between the large circular recess and the hinge edge. Mixing the two can give you a neat row of holes in entirely the wrong place. Find the boring diagram for the actual hinge and plate combination before choosing a jig.

Look at where the arrows end. A measurement to the center of the circle is not the same as one to its rim. Both manuals provide a conversion chart for center-based drawings. For example, each lists a 4 mm cam setting for a drawing that gives 22 mm from the door edge to the cup center. Do not try to put 22 mm on an offset knob. Once you know which dimension you have, the meaningful comparison is quite short: both jigs cover 3, 4, 5 and 6 mm; only Milescraft lists 2.5 and 7 mm.

Next check what the door looks like from the front. A routed groove, recessed panel or glass opening can leave less material behind the proposed hole than you measured at the outer edge. Put the hinge over its intended spot on the back and check the entire cup footprint against the construction of the door. If the chosen hardware requires more solid material than you have there, changing drilling guides is not a solution.

Match new doors to the old cabinet plates

Suppose an old door fits its opening nicely but has peeling laminate. Keeping the cabinet plates preserves the parts of the installation that already work. Before discarding the old door, label its top, hinge edge and opening. Record each hinge center from the same end. Two hinges that look symmetrical need not actually be spaced alike. Check the old and new doors for equal height before copying the numbers; a deliberately different door height can change where the reference should be.

Lay the two doors with their backs up, hinge edges parallel and identified tops aligned. If their dimensions and intended positions match, transfer the lines and square them across the new hinge stile, the upright strip that carries the hinge. A 12-inch combination square lets you register against the straight edge and draw a line long enough to see beside the jig. Use a pencil on the back or mark on removable tape outside the spot where the jig sits.

The Kreg base can be centered directly on those lines. Its instructions call for at least two inches between the door end and cup center so that both indexing cams can bear against the hinge edge. The Milescraft end pin offers a physical stop at three or four inches, handy if those are the dimensions you need. An existing center at three and a half inches is a reason to use a measured line, not a reason to move a working cabinet plate half an inch.

Use one offcut to check depth and screw position

Before drilling the new door, make a sample using material that matches its thickness and, if possible, its construction. A scrap of thick construction lumber will show whether the bit is turning, but not whether the point leaves a blemish on the outward face of a thinner cabinet door. Mark the back of the sample, clamp the jig as directed and keep hands away from both the bit and the underside of the cut. The Kreg manual specifies two clamps, one on either side of the guide socket.

The Kreg collar sits against a shoulder on the supplied bit. A spare 35 mm bit of a different length is not a substitute simply because the diameter is right. On the Milescraft, use the fixture marked for the depth your hinge requires; 12.7 mm and 13 mm are separate choices. Once the sample is drilled, clean out the chips and set the hinge cup into it without screws. The flange should sit as the hinge drawing shows. Do not use screw pressure to pull a high flange down into a shallow hole.

Now look at the two small fastening holes. The round cup can fit even if the screw pattern does not. Milescraft illustrates a pattern labeled 45 by 9.5: the first number is the spacing between fasteners, the second locates that row relative to the cup center. Compare the pattern with your hinge rather than drilling every available guide hole. Check pilot diameter and depth against the screws as well. A stop collar on the large boring bit does nothing to stop the separate, small pilot bit.

Lay out the cabinet side when there are no old holes

An empty cabinet opening changes the choice. You must match two sets of locations: cups on the door and mounting plates inside the cabinet. On a stack of identical new doors, the Milescraft pin can register each upper cup from the top and each lower cup from the bottom, provided the plan calls for a three- or four-inch end distance. For a middle hinge, mark its own centerline. Pinning the two end holes does not locate the middle one or decide how many hinges the finished door needs.

Before unclamping the Milescraft, use its centering marks to extend the cup line on the door. Hold or support the door in the intended position with the specified gap, then transfer that line to the cabinet. Its removable marking guide helps locate plate holes on a face frame or cabinet wall. The line tells you the height; the particular plate drawing tells you the setback. A face-frame plate and a frameless plate can sit on different surfaces even when their hinges accept the same 35 mm cup.

With the Kreg, the door-side work is the same purchase you needed for a replacement, but the cabinet layout is a separate measuring job. Plan somewhere to place the clamps before you buy one for a narrow framed door. The six-inch trigger clamp comparison distinguishes throat depth from jaw opening: a clamp can open wide enough for the door and bench yet still not reach a flat clamping spot on the jig.

Hang one door before boring the batch

Start with one door and its own hinges, not every left-hand door in the stack. Check the closed gaps at the top and hinge side, then slowly open it and look for contact with the adjacent door, frame or shelf. If the flange sits flat but the plate and hinge arm meet at different heights, recheck the transferred centerline. If they meet at the same height but the door covers the wrong part of the frame, verify the hinge, plate and cup offset before copying that setup.

For a run of mirrored doors, label the top and hinge edge on the back of every blank while the doors are still arranged as they will hang. Save the approved offcut and note its cam setting, the hinge part number and the reference end. Returning to the job after painting is easier when you can put the example in your hand. And if a replacement arrives already bored, try the actual hardware first: when the cup, screw pattern and cabinet plates already match, the useful purchase may be neither jig.

Official sources and further reading

Sources reviewed on November 9, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.