Laynie Hasan.

← All offer guides

Workshop Tool Comparisons · Reviewed November 8, 2026

Kreg Shelf Pin Jigs: 5 mm vs 1/4 Inch for Cabinets

Pull a shelf pin from the cabinet and measure the round stem that goes into the wall. A 5 mm stem points to the Kreg KMA3232; a 1/4-inch stem points to the KMA3225. Both jigs space holes 32 mm apart, and both accept Kreg bits for either size. If you already own one, you can change the hole diameter without buying the other jig.

Best for

Building a bookcase with movable shelves or extending a cabinet row after confirming its pin diameter and hole spacing.

Probably not for

Repairing crumbled shelf holes, attaching fixed shelves, or adding holes to thin dividers without checking the available depth.

Specifications at a glance

Manufacturer specifications for the exact versions compared
Cabinet decisionKreg KMA3232Kreg KMA3225
Supplied hole size5 mm1/4 inch (6.35 mm)
Pin stem to match5 mm1/4 inch
Guide layoutSix drill guides, spaced 32 mm on centerSix drill guides, spaced 32 mm on center
Distance from side of jig to guide center37 mm37 mm
Continue the rowExtension and double-ended indexing pinExtension and double-ended indexing pin
Change diameter laterAdd Kreg KMA3210 bit and 1/4-inch pinsAdd Kreg KMA3215 bit and 5 mm pins

As an Amazon Associate I earn from qualifying purchases.

Kreg KMA3232 Shelf Pin Jig, 5 mm

The 5 mm kit makes sense when the cabinet, your shelf-support hardware or a furniture plan already calls for that diameter. The steel guides handle the spacing; the supplied bit cuts the hole that takes the pin.

Pros

  • Supplied bit matches 5 mm shelf-pin stems without an accessory purchase
  • Can be used with the Kreg 1/4-inch shelf-pin bit for a later build

Cons

  • An existing 1/4-inch support will not fit the supplied hole size
  • Still needs a matching 32 mm pattern to continue a factory-drilled row

Who it’s for: Choose it to add positions to a bookcase with measured 5 mm pins and compatible spacing. Skip it if every shelf support you intend to use has a quarter-inch stem.

Check Kreg KMA3232 Shelf Pin Jig, 5 mm on Amazon

Kreg KMA3225 Shelf Pin Jig, 1/4 Inch

This kit starts with the larger of the two holes. It suits a shop building cabinets around a stock of quarter-inch supports. The larger diameter does not give a different step between shelf heights.

Pros

  • Supplied bit fits a project specified for quarter-inch pins
  • Uses the same two-size indexing system as the 5 mm kit

Cons

  • A 5 mm stem will be loose in the hole cut by the included bit
  • Larger hole diameter is not a shelf load rating

Who it’s for: Choose it for a pantry where you plan to reuse quarter-inch supports across several bays. For an existing cabinet with smaller pins, match those first.

Check Kreg KMA3225 Shelf Pin Jig, 1/4 Inch on Amazon

Read the pin, then read the row

Put one of your existing supports on a sheet of paper and trace it. The short round stem on one side of the drawing is the part you need to size. The spoon, ledge or pad on the other side holds the shelf; its width tells you nothing about the hole to drill. Use calipers on the stem, or look up the part number on the hardware packet. A quarter inch is 6.35 mm, not another name for 5 mm.

Now look at the holes as a group. The jig sets their centers 32 mm apart, regardless of which bit came in the box. In a row of six holes there are five spaces from the first center to the sixth, so the expected distance is 160 mm. Measure across several spaces if you can: it is easier to spot a row on some other pitch over that distance than by judging a single gap. Matching the pin alone does not make a row compatible.

For a kitchen cabinet with a working shelf, borrow a pin from a sound hole and put it back afterward. A battered hole where a shelf fell is a poor reference for purchasing a jig. If the goal is simply one more shelf and four empty holes already line up at the right height, buy matching supports and cut the shelf to fit. There is no drilling decision left for either Kreg to solve.

Lay out four supports, not one impressive row

Picture a bookcase on the bench before its sides are joined. Label the inside faces left and right, then mark the top and front on both. Choose the same end of the jig as your starting reference for all four rows. Starting the left panel at its top and the right panel at its bottom can produce two tidy rows that never give a shelf four supports at the same height.

Make a pencil mark for a single shelf position on both side panels. Check the front and back rows at that height before committing to the rest. On a frameless cabinet the fence references the panel edge; when moving to the back row, Kreg shows moving the fence to the opposite side of the jig. A face frame gives you a different edge to work from. Use the face-frame diagram instead of assuming the front lip represents the side panel.

For a retrofit, compare the center of an existing hole with the proposed guide center before drilling. The guide center is 37 mm from the side of this jig. That is not a guarantee that your cabinetmaker used a 37 mm setback. A combination square for transferring offsets helps you carry an existing measurement from one panel to the other. If the jig cannot sit flat in the position you need, stop before making the first hole.

Find out where the point stops

Use an offcut of the side material, not just any block of wood on the bench. Set the collar on the bit using the molded recess on the back of the jig as Kreg illustrates. Clamp the work and jig, wear eye protection and drill the sample. Try the actual support: the stem should seat far enough for its shoulder to meet the surface, and the point of the bit should not have broken through the other face.

The offcut can answer a second question if you are building two shelf bays around a common divider. A blind hole made from the left can meet a hole at the same height drilled from the right, even if neither hole alone would pass through the board. Compare the two planned depths with the thickness of the divider before laying out opposing rows. If the layout leaves inadequate material between them, change the divider design or support arrangement rather than assuming either kit fixes it.

In an assembled cupboard, try positioning the unpowered drill, jig and clamp together. A guide that lines up beautifully is little help if the clamp cannot reach it or the drill chuck runs into the opposite wall. The six-inch trigger clamp comparison distinguishes how far the jaws open from how far they reach in from an edge. That second dimension matters when the clamp pad needs to land on the jig rather than on a projecting face frame.

Add a shelf position where it earns its keep

Say the tall olive oil bottle fits on the lowest pantry shelf but the shelf above wastes space over the jam jars. Put the jars and the next shelf into the cabinet before choosing a new position. Count the usable steps in the row: moving up one hole changes support height by 32 mm; moving two changes it by 64 mm. Allow room to lift a jar out, not only enough room for its lid to clear the shelf at rest.

If the desired position falls beyond the six guides, keep one measured reference rather than drawing a fresh starting line each time. For a run progressing downward, the manual shows attaching the extension to the top of the jig and indexing it to the last drilled hole. Clamp again, then drill through the metal guides. The hole in the extension locates the indexing pin; it is not a seventh drill guide. Use the end of the indexing pin that fits the hole you just made.

Before filling the pantry, set an empty shelf on the new supports and press lightly over each corner. A corner that rocks deserves a look underneath. Check that all four supports sit in corresponding holes, that their shoulders are seated, and that all four have the same ledge shape. A replacement pin with the right stem can still have a different ledge height. Making a larger hole is not a remedy for four mismatched supports.

When to buy a bit instead of another jig

Suppose you own the KMA3225 from building garage cabinets, but now need 5 mm holes for a bookcase. Kreg lists the KMA3215 as the compatible 5 mm shelf-pin bit. Pair it with matching supports, use the appropriate end of the indexing pin and set the collar for the replacement bit. The reverse change uses the KMA3210 quarter-inch bit. Check the number on the jig you actually have; these recommendations are for the two models compared here.

Buying a second body solves a different problem. Kreg lets you connect bodies for a longer run, which could suit a shop repeatedly drilling tall sides. For a single extra shelf in an inherited bookcase, that is unnecessary. Keep one marked sample of the correct pin with the jig or label its bag with the cabinet name. The next time a shelf goes missing during a move, you can replace its hardware without having to identify the hole all over again.

Official sources and further reading

Sources reviewed on November 8, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.