Laynie Hasan.

← All offer guides

Cycling Tool Comparisons · Reviewed November 11, 2026

Park Tool CCP-22 vs CWP-7: Which Crank Puller Fits?

For a familiar square-taper bike with a conventional M8 crank bolt, the CCP-22 gives you a dedicated handle. If the next bike on your bench has a conventional Shimano Octalink or ISIS Drive crank, choose the CWP-7 and swap tips between bikes. If the crank already extracts itself, keep both tools off the shopping list.

Best for

A home mechanic removing a conventional three-piece crank arm, especially someone choosing between a dedicated tool for one bike and a compact shared kit.

Probably not for

Pulling a pedal out of a crank, servicing a self-extracting crank, repairing stripped extractor threads or removing a bottom bracket cup from the frame.

Specifications at a glance

Manufacturer specifications for the exact versions compared
At the bikeCCP-22 Crank PullerCWP-7 Compact Crank Puller
Extractor thread in the crank armM22 x 1.0M22 x 1.0
Conventional square taper with M8 crank boltUse its fitted tipUse the 11.3 mm tip
Conventional Octalink or ISIS DriveNot the right pullerUse the 16.3 mm tip on the compatible system
What turns the driverBuilt-in handleSeparate 15 mm wrench or adjustable wrench
What you keep track ofA handled tool with a floating tipA compact driver with a removable tip stored at each end
Where both stopNo substitute for intact arm threadsChanging tips does not change the outer thread

As an Amazon Associate I earn from qualifying purchases.

Park Tool CCP-22 Crank Puller for Square Taper Cranks

A long-handled extractor with a floating tip. A typical fit is a conventional square-taper arm with M22 x 1.0 extractor threads and an M8 fixing bolt.

Pros

  • Handle stays with the extractor
  • No small-versus-large tip decision for a known, compatible bike

Cons

  • Does not cover Octalink or ISIS Drive cranks
  • Fixed handle takes more room in a shallow tool tray

Who it’s for: A good choice for repeated work on a known square-taper setup, especially if you want to reach for one tool after removing the crank bolt.

Check Park Tool CCP-22 Crank Puller for Square Taper Cranks on Amazon

Park Tool CWP-7 Compact Crank Puller

A wrench-driven extractor with 11.3 mm and 16.3 mm swivel tips. It covers conventional square-taper and specified splined interfaces with the same extractor body.

Pros

  • Both working tip sizes travel on the tool
  • Works with a wrench you may already own

Cons

  • Needs a separate wrench to turn the driver
  • The correct tip must be on the working end before use

Who it’s for: Makes sense when one tool has to cover a square-taper commuter and a compatible Octalink or ISIS Drive bike.

Check Park Tool CWP-7 Compact Crank Puller on Amazon

Which end of the crank arm needs to come off?

Follow the crank arm from the pedal toward the middle of the bicycle. At the outside end, the pedal threads into the arm. At the inside end, the arm fits onto the bottom bracket spindle, the shaft that turns through the frame. These pullers work at the inside end. If the plan is to move your favorite pedals to another bike, leave the crank arms in place. Our Park Tool PW-4 and PW-5 pedal wrench comparison covers pedals with external wrench flats; some pedals instead take a hex key from the back.

Replacing a damaged square-taper crank arm is a different job. Removing its fixing bolt releases the fastener, but the arm may still sit firmly on the tapered spindle. Picture two pieces of the puller moving relative to each other: the outer piece threads into the arm, and the driver in the middle pushes against the end of the spindle. The arm comes away with the outer piece. It is the engagement between that outer piece and the arm that gives the tool something to pull on.

Read two sizes, not just the number on the hex key

Both pullers need M22 x 1.0 extractor threads. That is the large threaded opening in the crank arm: 22 mm nominal diameter, with a pitch of 1 mm. It is not the thread on the bolt that holds the arm on the spindle. The fixing bolt gives you another clue about which tip belongs against the spindle. A service sheet calling for an M8 fixing bolt is describing the bolt thread, not telling you to look for a hex key marked 8. Do not use the size of the wrench that fits the bolt head as your compatibility check.

Look for the model code on the crank itself, especially on a used bike. Its components may not match the ones in the original bicycle catalog. Find that crank model in the component maker’s service instructions and establish whether it uses an external puller at all. Then check the arm threads and spindle family against Park Tool’s fit list. A useful note to keep with the bike is as specific as “M8, square taper, standard extractor thread.” A note that says only “Shimano” leaves most of the shopping decision unresolved.

One square-taper bike: what the CCP-22 handle buys

Suppose the job is to exchange a bent left arm on a commuter whose conventional square-taper setup you have already identified. Either puller can do the removal. The CCP-22 earns its place here because its working handle is already attached. There is nothing to swap between the two arms and no driver wrench to retrieve from another drawer. If the tool lives on a hook above that commuter, the extra length of the handle costs little in storage and is useful each time the job comes around.

The handle does not remove the crank bolt for you. Look at the bolt head before clearing the bench and set out its matching socket or hex key. Keep a shallow dish for the bolt, any washer beneath it and any ordinary dust cap. The washer matters: a part left down in the recess changes what the puller can bear against. If you have the right crank puller but lack the tool for the fixing bolt, the built-in handle has simplified only the second half of the removal.

A shared kit: what the second CWP-7 tip changes

Now put two work tickets on the bench: a square-taper commuter and a mountain bike with a conventional Octalink crank. With the CWP-7, keep the 11.3 mm tip on the working end for the specified square-taper job, then fit the 16.3 mm tip for the Octalink job. The wider contact face belongs against the end of that larger hollow spindle. Do not choose the tip by which one passes into the hole most easily. You need it to bear on the spindle, not disappear down the middle.

Park Tool’s instructions show a foot at each end of the driver. When putting the tool away, give the spare foot its spot back. A CWP-7 found loose at the bottom of a secondhand tool chest with only one foot is not yet the two-interface kit in this comparison. Also count the wrench in your packing decision. The instructions specify a 15 mm wrench or an adjustable wrench for the driver. If your travel toolbox already contains one, the extractor adds little bulk; if not, the small body is only part of what you have to carry. Our Crescent and CHANNELLOCK adjustable wrench comparison covers jaw and handle differences if you are outfitting that box.

A cap and a damaged thread can each change the answer

A ring around the crank bolt can look like an ordinary dust cap, yet on a self-extracting crank it is part of the removal mechanism. As the bolt backs out it bears against that retaining ring and moves the arm off the spindle. Removing the ring first would take away the part the design relies on. If the maker identifies your crank as self-extracting, follow that system’s instructions. Owning the correct puller for another bike is no reason to dismantle this one the same way.

On a conventional puller-equipped crank, inspect the large threads before taking up any load. The outer fitting must be fully engaged, not just holding on by the first turn. If it starts crooked, stops partway, or the threads are visibly torn out, stop. More effort on the handle cannot give the fitting more sound metal to hold. Changing from the CCP-22 to the CWP-7 will not fix this particular problem: both use the same extractor thread. Have the arm assessed rather than sacrificing what remains of that thread to a second attempt.

Plan for the job after the arm is off

If the real goal is to replace a bottom bracket, these pullers simply expose it. Neither one engages the bottom bracket cup. Identify that separate fitting and the correct tool before making a bicycle you depend on unavailable for the commute home. For an arm replacement, check the new arm’s interface and length rather than assuming that removal-tool compatibility makes two parts interchangeable. The CWP-7 can service both ISIS Drive and Octalink cranks, for example; that does not mean the cranks fit each other’s spindles.

Finally, have the crank maker’s installation instructions and torque specification ready for reassembly. A puller applies force to separate parts; its handle is no guide to how tight the fixing bolt should be when they go back together. For one confirmed square-taper bike, I would put the CCP-22 beside the bolt wrench. For a bench with both that bike and a compatible splined crank, I would keep the CWP-7, both feet and its driving wrench together. The distinction is what will actually be waiting on the bench next time.

Official sources and further reading

Sources reviewed on November 11, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.