Laynie Hasan.

← All offer guides

Outdoor Gear Comparisons · Reviewed November 5, 2026

Pelican 1010 vs 1040: Which Micro Case Fits Your Kit?

The Pelican 1040 adds 2.13 inches of inside length over the 1010, but only 0.07 inch of depth. Choose the 1040 if you want a card wallet and reader to lie next to each other. Choose the 1010 if the wallet is all you carry and you want to keep using the small pocket in your bag. If the problem is a thick plug or a tall control knob, look beyond these two cases.

Best for

Someone packing small electronics or accessories who can measure both the gear and the pocket where the closed case will ride.

Probably not for

Anyone who needs to operate a device underwater, conceal what is inside, or pack equipment taller than either interior.

Specifications at a glance

Manufacturer specifications for the exact versions compared
What to measurePelican 1010Pelican 1040
Black liner, clear case SKU1010-025-1001040-025-100
Interior length × width4.37 × 2.87 in6.50 × 3.87 in
Interior depth1.68 in1.75 in
Exterior length × width5.88 × 4.06 in7.50 × 5.06 in
Closed exterior depth2.12 in2.12 in
Weight without foam0.40 lb0.70 lb
Seal and closureRubber liner doubles as seal; latchRubber liner doubles as seal; latch

As an Amazon Associate I earn from qualifying purchases.

Pelican 1010 Micro Case, Black/Clear (1010-025-100)

Consider the 1010 for the little kit you take out of the bag as a unit: a wireless receiver and its adapter, for example. Measure them arranged the way you intend to carry them. A plug left attached is part of the receiver for this purpose, even if it barely registers when you look at the two pieces in your hand.

Pros

  • Shorter and narrower outside for a bag with a small accessory pocket
  • Weighs 0.30 pound less than the 1040 before adding gear

Cons

  • Less room to separate loose pieces in a single layer
  • The smaller footprint does not buy a thinner exterior

Who it’s for: Pick the 1010 for a compact group of pieces that you can lift out without tipping the case. Pass if the lid would have to push a coiled lead down to close.

Check Pelican 1010 Micro Case, Black/Clear (1010-025-100) on Amazon

Pelican 1040 Micro Case, Black/Clear (1040-025-100)

The 1040 makes sense for a longer object or for two smaller objects that you want to see at once through the clear lid. There is room to plan a left side and a right side, but the liner is not a partition. If one piece could scratch another, count a sleeve or separator as part of the load.

Pros

  • Adds a full inch of interior width for a side-by-side layout
  • Longer floor accommodates a kit that would need stacking in the 1010

Cons

  • Needs a wider opening in the carrying bag
  • Almost no additional interior depth for a bulky accessory

Who it’s for: Pick the 1040 when the extra floor space has a specific job. Skip it when the device already fits the 1010 and the extra space just leaves it free to move.

Check Pelican 1040 Micro Case, Black/Clear (1040-025-100) on Amazon

A card wallet and a reader on the same sheet of paper

Take a hypothetical camera kit: a card wallet measuring 3.25 by 2.25 inches, a reader measuring 2.5 by 1 inch and a small sleeve for the reader. Set the two bare rectangles end to end and they need 5.75 inches of length. That is longer than the 1010 interior. Turn the reader to run alongside the wallet instead and their combined width is 3.25 inches, wider than the 1010. A wallet that fits on its own is not the same purchase as a wallet plus reader.

On a sheet of paper, draw the 6.50 by 3.87 inch interior of the 1040. Place those same two pieces end to end. On paper you have three quarters of an inch left along the long side. Now put the reader in its sleeve, add the cord if you use one and leave room to get a finger under the wallet. A rectangle on paper cannot tell you exactly where the curved inside corners meet your gear, but it can tell you when an arrangement is already too long.

For a photographer who leaves the reader at the desk, repeat the exercise with just the wallet on the smaller outline. Bringing the 1040 solely to reserve an empty strip for a reader that stays at home makes little sense. If you are still choosing the reader itself, the Transcend RDF5 and Anker A8370 card reader comparison explains which host port each uses. Include any required adapter in your outline.

Why a flat layout can beat a second layer

Suppose you can make the contents fit the 1010 by putting the reader on top of the wallet. Before committing to that arrangement, set the stack on the table and measure its tallest point from the tabletop. Use a ruler across the top as a straightedge. Count the bump where the wallet snaps shut and the ridge on the reader sleeve. Two flat-looking objects often touch at those high points rather than across their broad faces.

Height is only half the question. Which piece do you reach for more often? If the wallet holds the card you need to change on a park bench, stacking a loose reader on top means finding somewhere to put it while the wallet is open. Keeping them side by side in the 1040 gives each a landing spot. If you unpack everything once, indoors, that convenience may not justify giving up the smaller pocket.

Size the zipper opening, not just the pocket

A pocket can be wider inside than it is at the zipper. Use the exterior dimensions for this check: cut a piece of cardboard the size of the closed case and build up its thickness to roughly 2.12 inches with folded paper. Try sliding it through the opening with the bag packed as usual. A flat paper outline alone can turn and bend in ways the polycarbonate shell cannot. Leave a little room to grasp the case on its way back out.

Also decide where the other items in that pocket will go. A hard rectangle may displace a lens cloth or notebook that used to bend around a corner. If your real aim is to separate a jacket and spare clothes from the rest of a pack, the Sea to Summit 13-liter dry bag comparison looks at flexible bags for that job. Reserve the rigid case for things that call for space of their own.

Look at the lip before closing the latch

Pelican uses the rubber liner itself as the seal on both cases. Give its rim an uninterrupted path to the lid. A fabric tab from a card wallet can sit across that path even when everything looks comfortably below the top. Fold the tab inward and tuck the end of a cord away from the edge. If you have to hold down the contents while fastening the latch, change the layout instead of counting on the latch to compress the kit.

Pelican gives both cases an IP67 water-resistance rating and describes an immersion limit of one meter for up to 30 minutes. The larger model does not change that limit. Neither is an underwater control housing: to swap a memory card or plug in a reader, you must open the lid. Pick a dry place for that step. For size, let your paper layout make the first cut and the opening of your actual bag make the last one.

Official sources and further reading

Sources reviewed on November 5, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.