Laynie Hasan.

← All offer guides

Art & Craft Comparisons · Reviewed November 12, 2026

Speedball Red Baron vs Nylon Baren for Hand Printing

For a few hand-printed cards and a tool you can also use to press down paper collage, choose the Red Baron 4142. Choose the Speedball 4139 if most of its time will be spent sliding over the backs of linocut proofs and edition sheets. Both discs measure four inches across. It is the smooth plastic face on one and the padded nylon face on the other that make them different purchases.

Best for

Printmakers working by hand on small relief blocks and paper crafters who also want to burnish flat pieces.

Probably not for

Rolling ink onto a block, lining up multiple colors automatically or applying press pressure to an entire plate at once.

Specifications at a glance

Manufacturer specifications for the exact versions compared
At the printing tableRed Baron 4142Speedball Baren 4139
Working faceSmooth plasticNylon covering over padding
Disc diameter4 inches4 inches
GripWooden handleWooden handle
Reason to choose itOne tool for block prints and flat paper craftsPadded, low-friction face for repeated rubbing on paper
On a block larger than the discMove across the image in overlapping passesThe nylon face still needs overlapping passes

As an Amazon Associate I earn from qualifying purchases.

Speedball Red Baron Baren, 4 inches, 4142

A hand baren with a wooden grip and a smooth plastic face. Speedball identifies the Red Baron as a tool for relief printing as well as book and card crafts.

Pros

  • Smooth face is easy to inspect before switching between crafts
  • Can press a paper panel into place as well as take an impression

Cons

  • No padded nylon layer beneath the printmaker’s hand
  • Four-inch disc can overhang small or narrow raised pieces

Who it’s for: Pick the Red Baron for a card table that handles a mix of printing and flat paper assembly.

Check Speedball Red Baron Baren, 4 inches, 4142 on Amazon

Speedball Block Printing Baren, 4 inches, 4139

The 4139 puts padding beneath a nylon working face. Its job is to slide across the back of the sheet while your hand supplies the pressure.

Pros

  • Nylon face designed to slide over the sheet
  • Padding between the rigid core and the paper

Cons

  • Same four-inch reach as the Red Baron
  • Covered face needs to stay clear of glue and dried ink

Who it’s for: Pick the 4139 for consecutive proofs or a small edition when you want a baren dedicated to clean paper.

Check Speedball Block Printing Baren, 4 inches, 4139 on Amazon

Which face belongs on your table?

Set a carved bird, a folded card and two pieces of colored paper on the table. If the plan is to print the bird on one piece and mount it on the other, the Red Baron has a job on both sides of the drying rack. Its smooth plastic face can rub the back of the sheet during printing and press the dry panel down during assembly. Use a clean cover sheet for the second job. The baren should not have to pass through a bead of glue to get to the next corner.

Change the project to a dozen impressions of the bird on separate sheets, with no collage afterward. Now the part of the tool you will use again and again is its sliding face. The 4139 has a nylon covering with padding behind it, where the Red Baron has smooth plastic against the sheet. That is a reason to choose the 4139 for a print-only bench. It is not a requirement for making an edition: if a Red Baron already moves comfortably over your chosen paper, the size and basic process will stay the same.

Baren and brayer sound close enough to confuse on a supply list. Check what is missing from yours. A brayer is the roller that carries ink to the raised design. A baren stays clean and presses from the back after paper meets ink. If you have a block, a tube of ink and no means of spreading it, settle the roller question first with the two-inch and four-inch Speedball brayer comparison.

A round disc on a rectangular block

Lay a four-inch paper circle over a four-by-six-inch postcard block before picking a tool. Even where its diameter spans the full width, the curved edge leaves the corners outside its reach. Moving the disc up to the other end misses different bits of the picture. On a print with a narrow border running around all four sides, plan a pass along each edge as well as across the middle. Both barens have exactly this geometry; the padded model does not cover a larger design in fewer placements by virtue of its face.

A two-inch square bookplate asks for less travel but a little more care. With half the disc hanging beyond an edge, leaning on the unsupported part can tip the baren and disturb the sheet. Put the grip over the supported design and use small movements. For a stack of bookplates with generous blank margins, it is the little image that needs pressure, not the entire sheet. Mark its approximate position on the backing board so you can find it after the paper hides the block.

Neither disc has a registration stop. If each bird needs to sit in the same place on a card, draw the outline of the open card and the block on a separate guide sheet. Align both to their marks before rubbing. For a second color, keep that guide for the next block. Low friction can be useful once the paper is in position, but the nylon on the 4139 cannot put a crooked second color back into register.

Read the proof before changing tools

Imagine the first proof shows a pale wing tip but the border beside it prints black. Before buying another baren, look at the inked block the next time the roller passes. Is there ink on the raised tip, or did the roller miss a low spot? Is the paper sitting on a scrap caught underneath the block? A padded disc changes the contact at the back of the sheet. It cannot put ink on a part of the design that was bare to begin with.

On the next impression, keep the sheet in place with one hand and lift just a corner to see the transfer, a technique Speedball shows in its printing demonstrations. If the edge still needs attention, lower the corner without shifting the rest. Once the whole sheet has been peeled away, trying to put it back by eye risks a second outline. Use another sheet for the next proof and keep the first one nearby as a map of the trouble spot.

Paper is another variable worth isolating. If the finished cards will be made of textured stock, save an offcut of that stock for a proof instead of relying only on a smooth sheet from the printer. Keep the same block and ink for the comparison. A smooth-paper proof and a textured-card proof answer a question about paper; changing the ink, paper and rubbing tool together makes it hard to tell which change mattered.

Keep the printing and assembly jobs separate

Suppose a community card workshop has one table for four people. Put the inking slab and roller at one end, the block and baren in the middle, and a place for wet impressions at the other end. Give the baren its own clean landing spot. A handle set down beside wet ink can mark the next person’s fingers even if the face never touched the slab. Fold and assemble the cards later, after the ink is dry enough to handle.

For the Red Baron, inspect the plastic under a light before moving it from a collage back to the printing area. A speck of dried adhesive is easier to remove before it leaves a mark on several clean sheets. On the 4139, keep glue work away from the nylon face in the first place. Neither face should be used to iron down a raised embellishment, flatten a fresh embossed panel or press directly on a wet image you intend to keep.

If the same motif is also going onto a cloth bag, choose ink for the bag before choosing a second pressure tool. The Speedball paper and fabric block ink comparison explains the distinction. Switching to a nylon baren does not make paper ink suitable for an item that will be washed. For cards alone, that fabric requirement need not drive the purchase.

When to keep the tool you already have

If most projects are single cards, occasional bookplates or a few sample prints before a block goes to a press, choose the Red Baron or keep the one in your kit. If your regular session means rubbing the backs of sheet after sheet, the 4139 offers a specific change you can name: the part that travels across the paper is padded and nylon-faced. That distinction gives you a better reason to switch than the words beginner or premium on a package.

For a large solid poster, sketch the actual image on scrap paper and move a four-inch circle across the area you would need to print. Now imagine doing it for every copy in the edition. If that amount of hand work is the obstacle, neither purchase changes it much. Look for access to a relief press that accommodates the block instead. Keep a baren for smaller jobs or for pulling the occasional proof at your own table.

Official sources and further reading

Sources reviewed on November 12, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.