Laynie Hasan.

← All offer guides

Workshop Tool Comparisons · Reviewed November 11, 2026

Stanley 12-220 vs 12-960: Block Planes for Fitting Wood

A box lid that almost fits may need to be shorter, narrower or just less sharp around the rim. Those are three different cuts. Pick the low-angle Stanley 12-960 if you regularly trim the sawn ends of solid wood. Pick the wider 12-220 if most of your work is along the edges, especially when the extra quarter inch of blade can cover the edge in one pass.

Best for

Woodworkers making small fitting cuts or chamfers on straight, accessible edges in solid wood, with a way to hold the piece steady and keep a plane iron sharp.

Probably not for

Flattening a large tabletop, thinning a stack of boards to a common thickness or trimming into a closed inside corner where the sole cannot travel.

Specifications at a glance

Manufacturer specifications for the exact versions compared
At the benchStanley No. 220 (12-220)Stanley Bailey 12-960
Angle at which the blade rests21°13.5°
Nominal cutter width1 5/8 inches1 3/8 inches
Best reason to choose itWider cut for general edge workLower bed for frequent end-grain trimming
Where the width mattersSpans a 1 1/2-inch edge when centeredNeeds overlapping cuts across that same edge
Replacement iron listed by Stanley0-12-508, nominal 40 mm12-504, nominal 35 mm
When neither fixes the problemA long, bowed edge needs a longer referenceA splintering exit edge still needs support

As an Amazon Associate I earn from qualifying purchases.

Stanley No. 220 Adjustable Block Plane, 12-220

A cast-iron block plane with a 21° bed, a finger rest at the front and a nominal 1 5/8-inch cutter. The linked listing is the individual plane, not a case of six.

Pros

  • The wider iron can cover an edge that the Bailey needs two passes to span
  • Useful for mixed work, including shallow chamfers and local edge fitting

Cons

  • Higher bed than the Bailey when the irons are honed alike
  • The short sole is a poor reference for straightening long edges

Who it’s for: Choose the 12-220 for solid shelf fronts, box sides and general trim when most cuts follow the grain.

Check Stanley No. 220 Adjustable Block Plane, 12-220 on Amazon

Stanley Bailey Low Angle Block Plane, 12-960

A cast-iron block plane with a cutter bedded at 13.5°, a nominal 1 3/8-inch iron and a quick-release cap for removing the blade.

Pros

  • Lower angle of attack for trimming ends with a similarly honed blade
  • Depth and alignment adjustments help set up a light, even shaving

Cons

  • Narrower cutter needs overlapping passes on thicker edges
  • A lower angle does not prevent the far corner of unsupported end grain from breaking out

Who it’s for: Choose the 12-960 for trimming short rails, evening a projecting end or fitting the length of a small solid-wood part.

Check Stanley Bailey Low Angle Block Plane, 12-960 on Amazon

Find the bind before choosing the plane

Set a drop-in wooden lid over its opening the way it will sit in use. Mark the front on the underside. Does the lid clear the two ends but rub along one side? Or can you slide it sideways while one end refuses to drop? In the first case you may need to narrow the lid along the grain. In the second you may have to shorten it across the grain. Those clues are worth more than the overall size of the box when deciding between these two Stanley planes.

There is a third possibility: one corner binds with the lid turned one way, but a different corner binds when you turn it around. Check the shape of the opening and the lid before taking anything off. A plane removes wood readily; it cannot tell which piece is out of square. Use a combination square against a known straight edge to check the adjoining end. Mark just the high area. Shaving both ends evenly would make a lid shorter without correcting a single crooked corner.

What 13.5° means at the end of a rail

Look at the end of a crosscut rail. The little open ends of the fibers face you; the long fibers are visible on its sides. When the plane travels across that sawn end, the iron has to sever those fibers cleanly rather than follow their length. The Bailey places its iron on a bed inclined at 13.5°, against 21° for the No. 220. Both block planes present the blade bevel up. With the same honing angle, the Bailey therefore brings the edge to the wood at a shallower angle.

Neither advertised number is the complete cutting angle. With bevel-up geometry the angle at the sharpened edge adds to the bed angle. If you sharpen the two blades differently, you can narrow or erase the distinction. Nor is the number a fine-cut setting: how far the iron projects determines the thickness it tries to take. On a box rail sawn just a hair long, pick the Bailey for the geometry, then set it to take a fine shaving. A deep bite is no substitute for a sharp edge when the aim is to fit an existing opening.

Keep the far corner on the workpiece

Imagine a box side with its outside face already dressed. A single pass across the end can look clean right up until the iron exits and a chip comes away from that face. The last fibers have nothing behind them. Hold a sacrificial wooden block tight against the exit side, flush with the surface you want to plane, so the iron travels into waste instead of out into space. Secure the assembly with the jaws clear of the blade path. Our trigger clamp comparison explains the difference between opening capacity and the reach needed to place a pad where it actually helps.

Without room for a backing block, approach from each outside edge toward the middle. Stop to check the end: two short approaches can leave a slight crown where they meet. Use a straight reference to find the high spot instead of planing one more full pass through the far corner. The lower bed on the 12-960 is a good reason to buy it for a batch of rail ends. It is not a reason to dispense with a backer. The same support can improve a one-off cut with the 12-220 you already own.

Where a quarter inch of blade changes the job

Take two pieces to picture the width difference. The first is a three-quarter-inch shelf with a sharp front corner. If you want only a narrow bevel, both irons are much wider than the cut. Mark the intended width lightly on the face and on the edge, and keep the two margins even as the bevel grows. Choosing the 12-220 here is a matter of favoring general edge work, not a claim that a wide blade automatically makes a wider chamfer. The angle you hold the plane and the wood you remove set that width.

Now consider an actual 1 1/2-inch-thick solid-wood piece whose edge is already straight but needs a light cleanup across its thickness. The nominal 1 5/8-inch cutter on the No. 220 leaves an eighth inch of width to spare. Centered and set evenly, it can span the edge. The Bailey cutter is an eighth inch shy, so it needs overlap. With the narrow iron, check both margins against the face as you work; riding the plane repeatedly along the more comfortable side can tip the edge away from square. This is one job where the modest difference on the spec sheet changes your handwork.

Before buying a second plane, read the shaving

If an existing plane skips at one corner of a board, use a firmly held offcut from the same piece to separate setup from grain direction. Set the blade to a very shallow cut. Try the left and right portions of the iron on the same narrow edge. If only one side cuts, check the lateral alignment before concluding that the plane is too wide or the bed too steep. If both sides cut but the wood tears in one direction along the long edge, reverse the piece and see whether the fibers lie down more cleanly.

A blade that needs sharpening is another reason to pause before changing models. In shopping listings the word iron means the blade alone, not the complete plane. Stanley names the 0-12-508 as the replacement for the No. 220 and the 12-504 for the Bailey 12-960. The two irons are different widths. Check the number on the tool and the replacement description together, particularly if you inherited an older plane. A sharp iron that fits the body you already have may be all you need to finish a short run of shelves.

A choice for the next piece, not every piece

For a set of box lids that need repeated adjustments at their end grain, take the Bailey. For a run of solid-wood shelf fronts with long edges to clean or corners to ease, take the No. 220. If the real problem is that a four-foot edge bows away from a straightedge in the middle, put both back on the list for another day. Their short soles can follow that hollow. A longer reference and a plan for straightening the edge matter there more than either cutter width or either bed angle.

Official sources and further reading

Sources reviewed on November 11, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.