Laynie Hasan.

← All offer guides

Workshop Tool Comparisons · Reviewed November 9, 2026

SUIZAN Flush Cut Saws: One Edge or Two for Wood Plugs?

For a bench where oak plugs alternate with soft cedar pegs, the SFL-001 puts two tooth patterns on one blade. For a run of identical plugs, the SC-003 gives you one cutting edge, a toothless back and a named replacement blade. Both have the same blade length. The wood sticking out of the surface, and the room beside it, are better guides than the five-inch label.

Best for

Trimming the exposed ends of glued wooden dowels, screw plugs and pegs close to an accessible flat face before final finishing.

Probably not for

Cutting metal fasteners, breaking down boards, or reaching the bottom of a recess where the saw cannot lie alongside the projection.

Specifications at a glance

Manufacturer specifications for the exact versions compared
At the benchSUIZAN SFL-001SUIZAN SC-003
Tooth patternTwo edges: hardwood 17 TPI; softwood 25 TPIOne edge: 22 TPI
Blade length120 mm120 mm
Overall length270 mm270 mm
Blade thickness0.30 mm0.40 mm
Kerf (width of the cut)0.30 mm0.45 mm
Opposite the working teethSecond toothed edgeUntoothed back

As an Amazon Associate I earn from qualifying purchases.

SUIZAN SFL-001 Double-Edge Flush Cut Saw

The two edges are intended for different woods. Turn the saw over to change the tooth spacing without changing handles. The plate and the listed kerf are each 0.30 mm.

Pros

  • Two wood-specific patterns on the complete saw
  • Narrower listed kerf of the pair

Cons

  • Second row of teeth needs clearance even when idle
  • Thinner plate needs a light return stroke, not pressure from the handle

Who it’s for: Choose it if plugs and pegs in different woods turn up regularly on an open bench. A second tooth pattern buys little for a single repeated cut in the same dowel stock.

Check SUIZAN SFL-001 Double-Edge Flush Cut Saw on Amazon

SUIZAN SC-003 Single-Edge Flush Cut Saw

This complete compact saw has a single 22 TPI cutting edge. SUIZAN identifies a separate flush-cut replacement blade, so the handle can stay in use if the teeth are damaged.

Pros

  • No second tooth row facing the neighboring rail
  • SCRP-003 replacement blade is identified by model

Cons

  • No second pitch for changing woods
  • Not shorter than the double-edge saw, despite the compact name

Who it’s for: Choose it for batches of matching cabinet plugs, especially if keeping the same handle and a known spare matters. It will not solve a clearance problem caused by the handle itself.

Check SUIZAN SC-003 Single-Edge Flush Cut Saw on Amazon

Which wood is actually under the teeth?

A maple dowel sticking out of a cedar box makes a useful buying example. The cedar is the face you want to preserve; the maple is the part you will saw. Choose the SFL-001 edge for the dowel, not the box. SUIZAN assigns the 17 teeth-per-inch edge to hardwood and the 25 teeth-per-inch edge to softwood. Those are two choices for flush trimming, not the rip and crosscut edges you might expect on a larger Japanese two-sided saw.

Now change the job to a dozen identical plugs on a bookshelf. Once the first plug cuts the way you want, the other eleven do not ask anything new of the blade. The SC-003 keeps the same 22 TPI pattern whichever face of the blade you put down. That is a practical advantage if you turn the work around on the bench halfway through: there is no second set of teeth to identify before starting again.

If the dowel came out of an unmarked bin, save a short piece for a trial cut. Glue it into a hole in an offcut with the same amount protruding as on the project. Sawing through a long rod in midair tells you little about what happens at the last fibers of a plug surrounded by finished wood. The sample also tells you whether you are comfortable getting close with the saw or would rather leave a little wood for hand finishing.

Make room for the handle and the idle edge

On a flat door laid on the bench, you can usually approach a plug from either end. A plug beside a raised cabinet rail gives you fewer choices. Picture the handle at the start and the end of the pull, not just the teeth resting against the plug. Both tools measure 270 mm overall with a 120 mm blade. A shorter-sounding product name does not buy another inch of clearance inside a narrow box.

The single-edge saw lets you face the plain back toward a rail while the cutting edge meets the plug. The back still needs space; letting it rub the rail can mark a finish or turn the blade off line. With the double-edge saw there are teeth on that side as well. If the piece is still loose, turning it a quarter turn or trimming the plugs before fitting the next rail may do more for access than changing saws.

Arrange the clamp so its body and handle sit outside the path of your pulling hand. The six-inch trigger clamp comparison explains throat reach: that measurement determines whether a pad can land on sound wood while the bar stays clear of the cut. If a small part can only be held with fingertips near the teeth, secure it to a larger backing board before picking up either saw.

Protect a finished face with a card

A proud plug on an unfinished bread box and one on a varnished cabinet call for different stopping points. On the bread box, a little hand sanding is still part of finishing the whole panel. On the cabinet, sanding the surrounding varnish to erase a saw mark may leave a patch more obvious than the plug. Before sawing, decide which surface you are prepared to touch up. If the answer is only the plug, give the saw a physical barrier.

Punch or cut a hole in a clean piece of thin card and slip it over the plug so it lies flat. Pull the saw across the card, not across the cabinet finish. Its thickness deliberately leaves a small amount of plug above the face. Use a fresh piece if it picks up grit or tears; a ragged hole no longer protects the finish right beside the cut. On veneer, do the last bit of leveling on the plug itself, not by sweeping a power sander over the area.

The published kerfs are 0.30 mm for the SFL-001 and 0.45 mm for the SC-003. Kerf measures the slot the teeth remove. It is not a specification for how far a finished plug will stand above the surface. With a card under the blade, the card sets that distance. Choosing the thinner plate does not make the protective step unnecessary, and choosing the thicker one does not condemn the plug to a visible ridge.

Cut the plug without levering it out

Wait for the glue to cure as its maker directs. A plug that rotates or rocks is a fit or glue problem. Holding it still with the teeth until it severs may loosen the part that should remain in the hole. Clear away dried beads that would tip the blade and check that no screw, pin or hidden brad crosses the cutting path. Neither of these saws is a way to bring an exposed metal head down to the face.

Bring the blade close to parallel with the surface and start a short, gentle pull across the projection. Ease off as you send it back. Trying to make the return trip cut too is a good way to buckle a thin plate. At the far side, let the teeth sever the last fibers. Twisting off the little cap because it appears nearly free can pull a sliver from the plug below the line you aimed for.

A plugged pocket hole adds another wrinkle. The screw and the plug occupy the same angled hole, but only the wood above the face belongs in the cut. If the assembly is still at the joinery stage, the Kreg 310 and 320 pocket-hole jig guide covers laying out those holes. Plan the plug trimming before a second panel blocks the pull. If the screw head itself projects above the face, correct the joint before trying to cover it.

Buy the saw, or buy just the spare you need

For a shop making pairs of stools, it can help to keep a small offcut with one trimmed peg beside the jig. It records the peg species, how much was left proud and whether a protective card was used. If the next batch goes from walnut pins to cedar pegs, that is a reason to try the other SFL-001 edge. If nothing changes except the number of stools, there is little reason to change a satisfactory cutting setup.

Buying for an existing SC-003 is a different decision from choosing a first saw. Look for SCRP-003 when the handle is sound and only the blade needs replacement. SC-003 is the complete saw. The nearby listings for a versatile wood blade or a plastic and bamboo blade are not the flush-cut spare. Match the letters as well as the five-inch description, and do not assume that a spare for a single-edge saw fits the double-edge handle.

Finally, inspect what is left after trimming the sample. A plug that sits below the surface cannot be raised by taking an extra pass, and torn fibers at the rim will remain visible under a clear finish. Adjust the card or the approach while the sample is expendable. Once the method leaves an intact rim and just enough wood for the finish you plan, the choice between one edge and two has done its job.

Official sources and further reading

Sources reviewed on November 9, 2026. Prices, availability and terms can change; recheck before buying.

Commission disclaimer

This article contains affiliate links. If you buy or sign up through one of them, I may earn a commission at no extra cost to you. That commission does not change the price you pay or the criteria used in this guide. Product details, prices, availability, and terms can change, so confirm the current information on the linked page before buying.